change log edits after feedback from Michael

git-svn-id: https://svn.code.sf.net/p/freetel/code@1874 01035d8c-6547-0410-b346-abe4f91aad63

diff --git a/smartmic/SM1000-C/Change-Log-C.txt b/smartmic/SM1000-C/Change-Log-C.txt
index 0c346205b94ad759ad0c79ffcbffbb2ca2e2093b..e43daa537b994776dfa1398941838645a53f48ce 100644 (file)
--- a/smartmic/SM1000-C/Change-Log-C.txt
+++ b/smartmic/SM1000-C/Change-Log-C.txt
@@ -147,8 +147,10 @@ Status:    [ O] OPEN - no action taken,    [X] Complete, Schematic changes made, no
        J25 was added for external reset switch. Do you still want on board sw?\r
     Status: HEADER PROVIDED RGB 09/15/14\r
     \r
-28.    [X] 1nF to filter noise across 500k R42 but very close to op-amp.\r
+28.    [ ] 100pF to filter noise across 500k R42 but very close to op-amp.\r
        Status: Added. Correct placement? RGB 9/8/14.\r
+        4 Oct 2014; DGR Changed from 1nF to 100pF after testing with dynamic\r
+        microphone by Michael Wlid\r
 \r
 29.    [O] highly senstive net between R53 and R42 should be shorter if possible, \r
     as we are getting a lot of noise pick up.\r
@@ -312,13 +314,14 @@ renumber to correct for duplicate #31 RGB 9/8/14
                SignaLink cable will bring whatever is at the Rig Digital connector to the SM1000\r
                Status: Implemented parallel configuration  RGB 09/27/14\r
                \r
-63. [O] U3 (USB chip) is hot to touch, in normal operation and USB boot mode. \r
+63. [X] U3 (USB chip) is hot to touch, in normal operation and USB boot mode. \r
     + same chip isn't hot on Discovery\r
     + suspect this is a "David error" - e.g. wrong resistors loaded,\r
       pot is also glued to PCB nearby which may be shorting and USB\r
       connector has become detached once so there may be a short.\r
        Status: Open. Needs debug.      RGB 09/27/14\r
-       \r
+    4 Oct 2014: Michasel Wild doesn't report this issue, have concluded it a one off error on Davids board\r
+       \r
 64.  [O] Found soldering little wires to the RJ45 patch panel unwieldy.  Is there a better way?   Also should we separate the grounds for mic/spkr/ptt to rig?  mic grounds often separate on rig connectors.\r
        Status: could use thru hole part,but would require hand soldering - extra mfg operation         RGB 09/27/14\r
        \r
@@ -326,12 +329,19 @@ renumber to correct for duplicate #31 RGB 9/8/14
                [X] load C55 & C56, both 1nF, reduced switcher noise\r
                [X] add 100nF across R40, also reduced switcher noise\r
                [X] add 100uF 6.3V electrolytic (or tant) across R40, this reduced 50Hz frame rate noise\r
+                [ ] 100nF across R45\r
                [ ] Microphone bypass network:\r
-               [X] Add 100 ohm R in net between J3/R39\r
-        [X] Change C32 to 100uF 6.3V electrolytic (or tant) and move to junction of 100 ohm/R39 to AVSS\r
-        [X] add 100nF across 100uF C32\r
-               Status: A lot of new parts!\r
+                   [ ] Insert new 100 ohm R in net between J3/R39 (keep 2.2k)\r
+                    [ ] Change C32 to 100uF 6.3V electrolytic (or tant) and move to junction of 100 ohm/R39 to AVSS\r
+                    [ ] add 100nF across 100uF C32\r
 \r
+                    J3 - 100 ohm - 2200 ohm \r
+                                 |\r
+                     100nF parallel with 100 uF\r
+                                 |\r
+\r
+               Status: A lot of new parts!\r
+                  \r
 66. [X]        Change R48 to 10k, makes level adjustment on FT817 easier.  TBC on further radio testing.\r
        Status: Changed  RGB 09/27/14\r
        \r