test plan and change log updates

git-svn-id: https://svn.code.sf.net/p/freetel/code@1987 01035d8c-6547-0410-b346-abe4f91aad63

diff --git a/smartmic/SM1000-C/testplan.txt b/smartmic/SM1000-C/testplan.txt
index 68e93fca9a7fb266f73773dba3da60b10bf5e2a8..42759a8709f8a905e7c4dda86f64a8b1f88eddcc 100644 (file)
--- a/smartmic/SM1000-C/testplan.txt
+++ b/smartmic/SM1000-C/testplan.txt
@@ -1,21 +1,26 @@
 Test Plan for Rev C SM1000
 David Rowe 15/12/14
 
-[ ] 5V and 3V3 rails OK
-[ ] 1.24V across C14 and C15
+[X] 5V and 3V3 rails OK
+[X] 1.24V across C14 and C15
     + on chip regulator working
-[ ] Goes into USB DFU mode when PTT held down on power on/reset
+[X] Goes into USB DFU mode when PTT held down on power on/reset
     + STM32F4 BOOTLOADER device appears on Host PC USB port
     + note plug USB Cable in after power up, otherwise Host PC will
       supply power and prevent power cycle.
-[ ] Flash dac_ut.bin using USB on Linux:
+[X] Flash dac_ut.bin using USB on Linux:
     $ sudo apt-get install dfu-util
     $ sudo dfu-util -d 0483:df11 -c 1 -i 0 -a 0 -s 0x08000000 -D dac_ut.bin
     + if this works it will run for about 6 seconds then stop, you don't
       get a sucess message   
     + power cycle/reset 
-[ ] dac_ut works
-    + several volts PP audio freq  sine wave on test points P2/P3
+[X] dac_ut works
+    [X] several volts PP audio freq sine wave on test points P2/P3
+    [X] loud sine wave from speaker or headphones
+
+[X] 2.74V across MIC1
+[X] speak into mic, or tap board, sould be a few Vpp
+    + mic gain R42 roughly in the middle of travel
 
 TODO:
 (need more detail, pass/fail conditions)

diff --git a/smartmic/SM1000-D/change-log-D.txt b/smartmic/SM1000-D/change-log-D.txt
index 2956e3b84bb771014dd346da36f200b536b28f50..7564ff016890046fe59b86175801ab1c17c8a4b0 100644 (file)
--- a/smartmic/SM1000-D/change-log-D.txt
+++ b/smartmic/SM1000-D/change-log-D.txt
@@ -16,8 +16,12 @@
 
 7. [ ] Can't fit PCB into enclosure bottom with R46 volume control fitted.
 
-8. [ ] Not sure about tactile feel/quality of trim pots.  They seem to have varying tension/stifness and I can't seat a screwdriver properly in R52.
+8. [ ] Not sure about tactile feel/quality of trim pots.  They seem to have varying tension/stifness and I can't seat a screwdriver properly in R52.  I can rotate mic gain pot all the way around.
 
+9. [ ] Why are parts designators on overlay missing?  Rubbed off with cleaning?
 
+10. [ ] Assembly instruction: J3 needs to be loaded and jumper inserted
+
+11. Microphone pins are swapped, ie rotate by 180 degrees.