+++ /dev/null
-SM1000-E-CHANGE-LOG.TXT\r
-03/30/15 RGB\r
-\r
-1. [X] Change PTT sw. to e-switch LC2259OANP.\r
-\r
-2. [X] Change POWER SW to e-switch LC2259EENP.\r
- \r
-3. [X] Change SPKR CONN J4 to CONN-BOOM-XH-2A.\r
-\r
-4. [ ] Added part outlines to layer tDocu for documentation.\r
-\r
- In progress, adding to outlines in time.\r
-\r
-05/18/15\r
-\r
-5. [ ] Problem with SPKR OUT conn. Shorts output when stereo jack used.\r
-\r
-6. [ ] TrimPOT holes, location off by 1mm.\r
-\r
-7. [X] U1, CPU pins extend to the end of the pads.\r
-\r
- Corrected RGB\r
-\r
-8. [X] Lad pattern for LEDs too large. I will look into this. RGB\r
-\r
- No action todate.\r
-\r
-9. [X] SW5 land pattern too wide. Check specification.\r
-\r
- Corrected footprint RGB\r
-\r
-10. [X] C32, C59 footprint too short.\r
-\r
- corrected RGB\r
-\r
-11. [X] L1 Land pattern too wide.\r
-\r
- Corrected RGB\r
-\r
-12 [ ] CN4 Bubble after SMT(high temperature)\r
-\r
- No action yet. Edwin, can you find an alternative to fit? If different footprint, let me know and send specification so\r
- I can change it.(RGB)\r
-\r
-13. [X] R46 Easy to break R46 with handling.\r
-\r
- Add cement after production.\r
-\r
-14. [ ] PCB Problem reflowing CN10 USB connector.\r
- \r
- Make Breakaway 10mm (Edwin)\r
-\r
-15 [ ] PCB Stencil too small.\r
- \r
- MAke Stencil 52 x 52 cm(Edwin)\r
- \r
- \r
--- /dev/null
+SM1000-E-CHANGE-LOG.TXT\r
+03/30/15 RGB\r
+\r
+1. [X] Change PTT sw. to e-switch LC2259OANP.\r
+\r
+2. [X] Change POWER SW to e-switch LC2259EENP.\r
+ \r
+3. [X] Change SPKR CONN J4 to CONN-BOOM-XH-2A.\r
+\r
+4. [ ] Added part outlines to layer tDocu for documentation.\r
+\r
+ In progress, adding to outlines in time.\r
+\r
+05/18/15\r
+\r
+5. [ ] Problem with SPKR OUT conn. Shorts output when stereo jack used.\r
+ + as per Josh Mesaline email, suggest resistors to tip and ring\r
+ so a short doesn't upset amp. Does this mean it will work with\r
+ mono and stereo plugs? If stereo only we should note this in UG.\r
+\r
+6. [ ] TrimPOT holes, location off by 1mm.\r
+\r
+7. [X] U1, CPU pins extend to the end of the pads.\r
+\r
+ Corrected RGB\r
+\r
+8. [X] Lad pattern for LEDs too large. I will look into this. RGB\r
+\r
+ No action todate.\r
+\r
+9. [X] SW5 land pattern too wide. Check specification.\r
+\r
+ Corrected footprint RGB\r
+\r
+10. [X] C32, C59 footprint too short.\r
+\r
+ corrected RGB\r
+\r
+11. [X] L1 Land pattern too wide.\r
+\r
+ Corrected RGB\r
+\r
+12 [ ] CN4 Bubble after SMT(high temperature)\r
+\r
+ No action yet. Edwin, can you find an alternative to fit? If different footprint, let me know and send specification so\r
+ I can change it.(RGB)\r
+\r
+13. [X] R46 Easy to break R46 with handling.\r
+\r
+ Add cement after production.\r
+\r
+14. [ ] PCB Problem reflowing CN10 USB connector.\r
+ \r
+ Make Breakaway 10mm (Edwin)\r
+\r
+15 [ ] PCB Stencil too small.\r
+ \r
+ MAke Stencil 52 x 52 cm(Edwin)\r
+ \r
+16 [ ] Firmware Better debouncing software for push button switches (DR) \r
+\r
+17 [ ] Enclosure Move "Speaker Volume" text lower to clear volume control knob\r
+\r
+18 [ ] Enclosure Some variablility in gap between lid and front panel, gap is\r
+ sometimes wider on one side than another (Edwin)\r