Tuesday, July 07, 2014 04:05 PM\r
====================================\r
\r
-[ ] SW3 holes not big enough.\r
+[X] SW3 holes not big enough.\r
Hole is .5mm. Pin is .6mm. Hole should be 1.0mm per spec sheet. Will change. \r
+ 07/08/2014 - RGB\r
\r
-[ ] Is C26 rated at 25V in BOM? \r
+[X] Is C26 rated at 25V in BOM? \r
C26 is 25V in schematic, 16V in BOM. \r
OOPS! C23, C26, C40 & C46 should all be 25V. Will change database & BOM. Murata # GRM188R71E104KA01D, Digikey # 490-1524-1-ND, Part Def: CAP CER 0.1UF 25V 10% X7R 0603\r
-\r
- [ ] LED8 takes up whole of pads so diff to solder \r
- Will enlarge pad in library. \r
+ 07/08/2014 - RGB\r
+ \r
+[X] LED8 takes up whole of pads so diff to solder \r
+ Corrected package for LED-LTST - LED5 & LED8.\r
+ 07/09/2014 - RGB\r
\r
[ ] Is CN3 a standard size? My DC plugs don't fit in it \r
2.5mm ID, 5.5mm OD Plug. CONN PWR PLUG DC 2.5X5.5 8A MOD Digikey # \r
[ ] move R20 label close to R20 + I loaded R20 in the wrong place! \r
Will do. \r
\r
-[ ] is 4k7 missing from BOM or just my order? + I didn't have any in my Digikey order \r
+[X] is 4k7 missing from BOM or just my order? + I didn't have any in my Digikey order \r
Part definition error. Part # in part definition field. Will correct database & BOM.\r
This affects R2,R3, R4, R5 & R48. Should be Vishay Dale # CRCW06034K70FKEA, Digikey # 541-4.70KHCT-ND, Part Def: RES 4.70K OHM 1/10W 1% 0603 SMD\r
+ 07/08/2014 - RGB\r
\r
====================================\r
Tuesday, July 08, 2014 10:54 AM\r
====================================\r
\r
-[ ] Re C26, could u pls align the BOM and sch? I'm not sure which one has to change. \r
+[X] Re C26, could u pls align the BOM and sch? I'm not sure which one has to change. \r
C26 should be 25V to accommodate +16V power in max. \r
OOPS! Found that C23, C26, C40 & C46 all should be 25V. That's why I made them separate line item. I'll Change BOM to Digikey part # 490-1524-6-ND Murata # GRM188R71E104KA01D\r
-\r
+ 07/08/2014 - Same as #2 above - RGB\r
+ \r
[ ] Re CN3, Hmm, now I'm not sure! I dug around in the shed and found a connector that fits so I'm OK for now. \r
CN3 is Switchcraft RASM712PX 2.5mm ID, 5.5mm OD Plug. CONN PWR PLUG DC 2.5X5.5 8A MOD Digikey # CP3-002BH-ND\r
I've noted a problem, but will wait til you decide.\r
<layer number="16" name="Bottom" color="1" fill="1" visible="no" active="yes"/>
<layer number="17" name="Pads" color="2" fill="1" visible="yes" active="yes"/>
<layer number="18" name="Vias" color="2" fill="1" visible="yes" active="yes"/>
-<layer number="19" name="Unrouted" color="6" fill="1" visible="no" active="yes"/>
+<layer number="19" name="Unrouted" color="6" fill="1" visible="yes" active="yes"/>
<layer number="20" name="Dimension" color="15" fill="1" visible="yes" active="yes"/>
-<layer number="21" name="tPlace" color="7" fill="1" visible="no" active="yes"/>
+<layer number="21" name="tPlace" color="7" fill="1" visible="yes" active="yes"/>
<layer number="22" name="bPlace" color="7" fill="1" visible="no" active="yes"/>
<layer number="23" name="tOrigins" color="15" fill="1" visible="yes" active="yes"/>
<layer number="24" name="bOrigins" color="15" fill="1" visible="no" active="yes"/>
-<layer number="25" name="tNames" color="7" fill="1" visible="no" active="yes"/>
+<layer number="25" name="tNames" color="7" fill="1" visible="yes" active="yes"/>
<layer number="26" name="bNames" color="7" fill="1" visible="no" active="yes"/>
<layer number="27" name="tValues" color="7" fill="1" visible="no" active="yes"/>
<layer number="28" name="bValues" color="7" fill="1" visible="no" active="yes"/>
<layer number="199" name="Contour" color="7" fill="1" visible="no" active="yes"/>
<layer number="200" name="200bmp" color="1" fill="10" visible="no" active="no"/>
<layer number="201" name="Construction" color="7" fill="1" visible="no" active="yes"/>
-<layer number="202" name="TDIM" color="7" fill="1" visible="yes" active="yes"/>
+<layer number="202" name="TDIM" color="7" fill="1" visible="no" active="yes"/>
<layer number="203" name="BDIM" color="7" fill="1" visible="no" active="yes"/>
<layer number="204" name="BRD-DIM" color="7" fill="1" visible="no" active="yes"/>
<layer number="205" name="205bmp" color="7" fill="1" visible="no" active="yes"/>
<text x="-1" y="-1.6" size="1" layer="27" ratio="10" align="top-left">>VALUE</text>
</package>
<package name="LED-LTST">
-<smd name="C" x="-0.75" y="0" dx="0.8" dy="0.8" layer="1" roundness="25"/>
-<smd name="A" x="0.75" y="0" dx="0.8" dy="0.8" layer="1" roundness="25"/>
-<wire x1="-1.5" y1="0.7" x2="-1.5" y2="-0.7" width="0" layer="39"/>
-<wire x1="-1.5" y1="-0.7" x2="1.5" y2="-0.7" width="0" layer="39"/>
-<wire x1="1.5" y1="-0.7" x2="1.5" y2="0.5" width="0" layer="39"/>
-<wire x1="1.5" y1="0.5" x2="1.5" y2="0.7" width="0" layer="39"/>
-<wire x1="1.5" y1="0.7" x2="-1.5" y2="0.7" width="0" layer="39"/>
+<smd name="C" x="-1.25" y="0" dx="1.5" dy="1" layer="1" roundness="25"/>
+<smd name="A" x="1.25" y="0" dx="1.5" dy="1" layer="1" roundness="25"/>
+<wire x1="-2.2" y1="0.7" x2="-2.2" y2="-0.7" width="0" layer="39"/>
+<wire x1="-2.2" y1="-0.7" x2="2.2" y2="-0.6" width="0" layer="39"/>
+<wire x1="2.2" y1="-0.6" x2="2.2" y2="0.6" width="0" layer="39"/>
+<wire x1="2.2" y1="0.6" x2="2.2" y2="0.7" width="0" layer="39"/>
+<wire x1="2.2" y1="0.7" x2="-2.2" y2="0.7" width="0" layer="39"/>
<wire x1="-0.1" y1="0.5" x2="-0.1" y2="0" width="0.125" layer="21"/>
<wire x1="-0.1" y1="0" x2="-0.1" y2="-0.5" width="0.125" layer="21"/>
<polygon width="0" layer="21">
<attribute name="NAME" x="6.8" y="49.7" size="0.8128" layer="25" ratio="10"/>
<attribute name="VALUE" x="5.4625" y="49.25" size="1" layer="27" font="vector" ratio="10" rot="R270"/>
</element>
-<element name="LED5" library="_Coherix" package="LED-LTST" value="LED-RED,V" x="21.25" y="44.5" locked="yes" smashed="yes" rot="R270">
-<attribute name="NAME" x="21.8" y="42.05" size="0.8128" layer="25"/>
+<element name="LED5" library="_Coherix" package="LED-LTST" value="LED-RED,V" x="21.25" y="44" locked="yes" smashed="yes" rot="R270">
+<attribute name="NAME" x="22.2" y="42.05" size="0.8128" layer="25"/>
</element>
<element name="R17" library="AA-ipc-7351-resistor" package="RESC1608X55N" value="1K,1%" x="18.75" y="44.5" locked="yes" smashed="yes" rot="R90">
<attribute name="NAME" x="19.8" y="42.85" size="0.8128" layer="25" rot="R180"/>
<element name="R33" library="AA-ipc-7351-resistor" package="RESC1608X55N" value="2.2K,1%" x="5" y="48" locked="yes" smashed="yes" rot="R270">
<attribute name="NAME" x="4" y="49.7" size="0.8128" layer="25"/>
</element>
-<element name="LED8" library="_Coherix" package="LED-LTST" value="LED-RED,RA" x="2.5" y="48" locked="yes" smashed="yes" rot="R270">
-<attribute name="NAME" x="1.2" y="45.5" size="0.8128" layer="25"/>
+<element name="LED8" library="_Coherix" package="LED-LTST" value="LED-RED,RA" x="2.5" y="48.5" locked="yes" smashed="yes" rot="R270">
+<attribute name="NAME" x="0.8" y="45.4" size="0.8128" layer="25"/>
</element>
<element name="CN9" library="_RoweTel" package="MJ-3523-SMT" value="MJ-3523-SMT" x="43" y="8" locked="yes" smashed="yes" rot="MR270">
<attribute name="NAME" x="38.5" y="5" size="1" layer="26" ratio="10" rot="MR90"/>
</polygon>
<wire x1="18.75" y1="46.95" x2="21.25" y2="46.95" width="0.4" layer="1"/>
<polygon width="0.2" layer="1" isolate="0.3">
-<vertex x="3.5" y="50"/>
-<vertex x="1" y="50"/>
+<vertex x="3.5" y="51"/>
+<vertex x="1" y="51"/>
<vertex x="1" y="46"/>
<vertex x="6.5" y="46"/>
<vertex x="6.5" y="44.5"/>
<wire x1="23.75" y1="47.52" x2="23.75" y2="48.55" width="0.4" layer="1"/>
<wire x1="23.75" y1="48.55" x2="21.25" y2="48.55" width="0.4" layer="1"/>
<wire x1="18.75" y1="48.55" x2="21.25" y2="48.55" width="0.4" layer="1"/>
-<wire x1="18.75" y1="45.3" x2="19.7" y2="45.3" width="0.2" layer="1"/>
-<wire x1="19.7" y1="45.3" x2="20.5" y2="44.5" width="0.2" layer="1"/>
-<wire x1="20.5" y1="44.5" x2="22" y2="44.5" width="0.2" layer="1"/>
-<wire x1="22" y1="44.5" x2="22.5" y2="45" width="0.2" layer="1"/>
+<wire x1="18.75" y1="45.3" x2="19.2" y2="45.3" width="0.2" layer="1"/>
<wire x1="22.5" y1="45" x2="22.5" y2="47" width="0.2" layer="1"/>
<wire x1="22.5" y1="47" x2="23.02" y2="47.52" width="0.2" layer="1"/>
<wire x1="23.02" y1="47.52" x2="23.75" y2="47.52" width="0.2" layer="1"/>
<wire x1="14.6" y1="46.1" x2="15" y2="46.5" width="0.4" layer="1"/>
<wire x1="15" y1="46.5" x2="17.05" y2="48.55" width="0.4" layer="1"/>
<wire x1="17.05" y1="48.55" x2="18.75" y2="48.55" width="0.4" layer="1"/>
+<wire x1="19.2" y1="45.3" x2="19.5" y2="45.3" width="0.2" layer="1"/>
+<wire x1="19.5" y1="45.3" x2="19.7" y2="45.3" width="0.2" layer="1"/>
+<wire x1="19.7" y1="45.3" x2="20" y2="45" width="0.2" layer="1"/>
+<wire x1="20" y1="45" x2="20" y2="44.5" width="0.2" layer="1"/>
+<wire x1="20" y1="44.5" x2="20.5" y2="44" width="0.2" layer="1"/>
+<wire x1="20.5" y1="44" x2="22" y2="44" width="0.2" layer="1"/>
+<wire x1="22" y1="44" x2="22.5" y2="44.5" width="0.2" layer="1"/>
+<wire x1="22.5" y1="44.5" x2="22.5" y2="45" width="0.2" layer="1"/>
</signal>
<signal name="+5V">
<contactref element="U2" pad="1"/>
<signal name="N$19">
<contactref element="LED5" pad="A"/>
<contactref element="R17" pad="1"/>
-<wire x1="18.75" y1="43.7" x2="21.2" y2="43.7" width="0.4" layer="1"/>
-<wire x1="21.2" y1="43.7" x2="21.25" y2="43.75" width="0.4" layer="1"/>
+<wire x1="18.75" y1="43.7" x2="18.75" y2="43.05" width="0.2" layer="1"/>
+<wire x1="18.75" y1="43.05" x2="19" y2="42.8" width="0.2" layer="1"/>
+<wire x1="19" y1="42.8" x2="19.05" y2="42.75" width="0.2" layer="1"/>
+<wire x1="19.05" y1="42.75" x2="21.25" y2="42.75" width="0.2" layer="1"/>
</signal>
<signal name="N$16">
<contactref element="R12" pad="2"/>
<approved hash="19,1,af4e38883f75a8b3"/>
<approved hash="19,1,ade23a243fe9a82f"/>
<approved hash="19,1,a8ba3f7c3fd1a817"/>
-<approved hash="19,1,c1ff063903fec438"/>
<approved hash="19,1,c4a7036103c6c400"/>
<approved hash="19,1,c35304950362c4a4"/>
+<approved hash="19,1,c1ff063903fec438"/>
<approved hash="19,1,2de63a203fe02826"/>
-<approved hash="19,1,2f4a388c3f7c28ba"/>
<approved hash="19,1,28be3f783fd8281e"/>
+<approved hash="19,1,2f4a388c3f7c28ba"/>
<approved hash="4,16,9dc4933833e8c785"/>
</errors>
</board>