SM1000-E-CHANGE-LOG.TXT\r
03/30/15 RGB\r
\r
-1. [X] Change PTT sw. to e-switch LC2259OANP.\r
+1. [X] Change PTT sw. to e-switch LC2259OANP.\r
\r
-2. [X] Change POWER SW to e-switch LC2259EENP.\r
+2. [X] Change POWER SW to e-switch LC2259EENP.\r
\r
-3. [X] Change SPKR CONN J4 to CONN-BOOM-XH-2A.\r
+3. [X] Change SPKR CONN J4 to CONN-BOOM-XH-2A.\r
\r
-4. [ ] Added part outlines to layer tDocu for documentation.\r
- In progress, adding to outlines in time.\r
+4. [ ] Added part outlines to layer tDocu for documentation.\r
+ In progress, adding to outlines in time.\r
\r
05/18/15\r
\r
-5. [X] Problem with SPKR OUT conn. Shorts output when stereo jack used.\r
- + as per Josh Mesaline email, suggest resistors to tip and ring\r
- so a short doesn't upset amp. Does this mean it will work with\r
- mono and stereo plugs? If stereo only we should note this in UG.\r
+5. [X] Problem with SPKR OUT conn. Shorts output when stereo jack used.\r
+ + as per Josh Mesaline email, suggest resistors to tip and ring\r
+ so a short doesn't upset amp. Does this mean it will work with\r
+ mono and stereo plugs? If stereo only we should note this in UG.\r
+ Changed connector to low profile locking type RGB\r
\r
- Changed connector to low profile locking type RGB\r
+6. [ ] TrimPOT holes, location off by 1mm.\r
\r
-6. [ ] TrimPOT holes, location off by 1mm.\r
+7. [X] U1, CPU pins extend to the end of the pads.\r
+ Corrected RGB\r
\r
-7. [X] U1, CPU pins extend to the end of the pads.\r
- Corrected RGB\r
+8. [X] Lad pattern for LEDs too large. I will look into this. RGB\r
+ Land pattern size recommended by vendor. If too large, need suggestion. RGB\r
\r
-8. [X] Lad pattern for LEDs too large. I will look into this. RGB\r
- Land pattern size recommended by vendor. If too large, need suggestion. RGB\r
+9. [X] SW5 land pattern too wide. Check specification.\r
+ Corrected package RGB\r
\r
-9. [X] SW5 land pattern too wide. Check specification.\r
- Corrected package RGB\r
+10. [X] C32, C59 footprint too short.\r
+ corrected package RGB\r
\r
-10. [X] C32, C59 footprint too short.\r
- corrected package RGB\r
+ 11. [X] L1 Land pattern too wide.\r
+ Corrected package RGB\r
\r
-11. [X] L1 Land pattern too wide.\r
- Corrected package RGB\r
-\r
-12 [X] CN4 Bubble after SMT(high temperature)\r
- No action yet. Edwin, can you find an alternative to fit? If different footprint, let me know and send specification so\r
- I can change it.(RGB)\r
+12 [X] CN4 Bubble after SMT(high temperature)\r
+ No action yet. Edwin, can you find an alternative to fit? If different footprint, let me know and send specification so\r
+ I can change it.(RGB)\r
***** Edwin reports other vendors parts do same. Action? RGB\r
\r
13. [X] R46 Easy to break R46 with handling.\r
Add cement after production.\r
- ***** Note, I accidently hit and moved pot removing PCB from case. Suggest applying cement prior to soldering RGB\r
+ ***** Note, I accidently hit and moved pot removing PCB from case. Suggest applying cement prior to soldering RGB\r
\r
-14. [X] PCB Problem reflowing CN10 USB connector.\r
- Make Breakaway 10mm (Edwin)\r
- ***** Vendor problem. RGB\r
+14. [X] PCB Problem reflowing CN10 USB connector.\r
+ Make Breakaway 10mm (Edwin)\r
+ ***** Vendor problem. RGB\r
\r
-15 [X] PCB Stencil too small.\r
- Make Stencil 52 x 52 cm(Edwin)\r
- ***** Vendor problem. RGB\r
+15 [X] PCB Stencil too small.\r
+ Make Stencil 52 x 52 cm(Edwin)\r
+ ***** Vendor problem. RGB\r
\r
-16 [ ] Firmware Better debouncing software for push button switches (DR) \r
- could be: more solid indication of in DV mode, like two beeps, two flashes\r
+16 [ ] Firmware Better debouncing software for push button switches (DR) \r
+ could be: more solid indication of in DV mode, like two beeps, two flashes\r
\r
-17 [ ] Enclosure Move "Speaker Volume" text lower to clear volume control knob\r
+17 [ ] Enclosure Move "Speaker Volume" text lower to clear volume control knob\r
\r
-18 [ ] Enclosure Some variablility in gap between lid and front panel, gap is\r
+18 [ ] Enclosure Some variablility in gap between lid and front panel, gap is\r
sometimes wider on one side than another (Edwin)\r
\r
-19 [X] PCB change power led from red to green, clip/error led from amber to red? \r
- LED1 GRN\r
- LED2 RED\r
- LED3 GRN\r
- LED4 RED\r
- ***** DO we need new LED packages?\r
-\r
-20 [ ] ?? Mel reported ESD events at Dayton causing SM1000 to crash.\r
- "Gerry and I did notice one thing... the SM1000 appears to be a little\r
- sensitive to ESD events caused by "walking across the carpet in tennis\r
- shoes in the booth and then touching the SM1000." It would stop\r
- working and require toggling power, however it always came back\r
- working ok."\r
-\r
- ***** Looking for 0402 or 0603 TVS with 5VDC holding voltage. RGB\r
- Need definition of where to put these. RGB\r
+19 [X] PCB change power led from red to green, clip/error led from amber to red? \r
+ LED1 GRN, LED2 RED, LED3 GRN, LED4 RED\r
+ ***** DO we need new LED packages?\r
\r
- ***** Is action rqd here? Anything we can do?\r
+20 [ ] ?? Mel reported ESD events at Dayton causing SM1000 to crash.\r
+ "Gerry and I did notice one thing... the SM1000 appears to be a little\r
+ sensitive to ESD events caused by "walking across the carpet in tennis\r
+ shoes in the booth and then touching the SM1000." It would stop\r
+ working and require toggling power, however it always came back\r
+ working ok."\r
+ ***** Looking for 0402 or 0603 TVS with 5VDC holding voltage. RGB\r
+ Need definition of where to put these. RGB\r
+ ***** Is action rqd here? Anything we can do?\r
\r
-21 [X] From Mel: DNL LED5 and LED8 to save a little power.\r
- DNL LED8 RGB\r
- DNL R33\r
- DNL LED5\r
- DNL R17\r
+21 [X] From Mel: DNL LED5 and LED8 to save a little power.\r
+ DNL LED8, DNL R33, DNL LED5, DNL R17\r
\r
-22 [X] From Mel: Is R42 wired backwards? Higher output CCW vs CW?\r
- Mirrored part, corrected problem. RGB\r
+22 [X] From Mel: Is R42 wired backwards? Higher output CCW vs CW?\r
+ Mirrored part, corrected problem. RGB\r
\r
-23 [X] From Mel: Silk screen pin numbers on. Can e make CN12 larger for older Hams?\r
- Added pin nos for 1,8,9,16 RGB\r
+23 [X] From Mel: Silk screen pin numbers on. Can e make CN12 larger for older Hams?\r
+ Added pin nos for 1,8,9,16 RGB\r
\r
-24 [ ] From Mel: green led too bright, increase R15 to 1500 ohms\r
- ***** WE should try this on all LEDs and evaluate. RGB\r
+24 [ ] From Mel: green led too bright, increase R15 to 1500 ohms\r
+ ***** WE should try this on all LEDs and evaluate. RGB\r
\r
-25 [ ] From Mel: different colour case options\r
+25 [ ] From Mel: different colour case options\r
\r
-26 [ ] From Mel: PTT being pulsed low on power up.\r
+26 [ ] From Mel: PTT being pulsed low on power up.\r
\r
-27 [ ] From Peter VK5APR, DC input connector hole offset down wrt to\r
- enclosure on his unit. Is this true on any other\r
- samples, or maybe a 1 off? RJ45 aperture in enclosure\r
- also slightly offset to left.\r
+27 [ ] From Peter VK5APR, DC input connector hole offset down wrt to\r
+ enclosure on his unit. Is this true on any other\r
+ samples, or maybe a 1 off? RJ45 aperture in enclosure\r
+ also slightly offset to left.\r
\r
-28 [ ] firmware Check analog speech level in digital mode.\r
+28 [ ] firmware Check analog speech level in digital mode.\r
projects / freetel-svn-tracking.git / commitdiff