git-svn-id: https://svn.code.sf.net/p/freetel/code@1758 01035d8c-6547-0410-b346-abe4f...

diff --git a/smartmic/SM1000-REV-B2/Change-Log-B2.txt b/smartmic/SM1000-REV-B2/Change-Log-B2.txt
index dab7f24b03d403c570a2f9fdbbfc797531f4e4ec..58ce94d20aa53a4e5baad1d4a726b3875bfd11a5 100644 (file)
--- a/smartmic/SM1000-REV-B2/Change-Log-B2.txt
+++ b/smartmic/SM1000-REV-B2/Change-Log-B2.txt
@@ -1,32 +1,30 @@
 \r
 Change Log for SM1000-REV-B2\r
 \r
-Tuesday, July 07, 2014 04:05 PM\r
-====================================\r
 \r
-[X] SW3 holes not big enough.\r
+1.  [X] SW3 holes not big enough.\r
                Hole is .5mm. Pin is .6mm. Hole should be 1.0mm per spec sheet. Will change. \r
                07/08/2014 - RGB\r
 \r
-[X] Is C26 rated at 25V in BOM? \r
+2.  [X] Is C26 rated at 25V in BOM? \r
                C26 is 25V in schematic, 16V in BOM. \r
                OOPS! C23, C26, C40 & C46 should all be 25V. Will change database & BOM.  Murata # GRM188R71E104KA01D, Digikey # 490-1524-1-ND, Part Def: CAP CER 0.1UF 25V 10% X7R 0603\r
                07/08/2014 - RGB\r
                \r
-[X] LED8 takes up whole of pads so diff to solder \r
+3.  [X] LED8 takes up whole of pads so diff to solder \r
                Corrected package for LED-LTST - LED5 & LED8.\r
                07/09/2014 - RGB\r
 \r
-[ ] Is CN3 a standard size?  My DC plugs don't fit in it       \r
+4.  [ ] Is CN3 a standard size?  My DC plugs don't fit in it   \r
                2.5mm ID, 5.5mm OD Plug. CONN PWR PLUG DC 2.5X5.5 8A MOD Digikey # \r
                CP3-002BH-ND \r
                This is probably most common size in USA. Change? \r
 \r
-[ ] couldn't solder bottom pad of U5 by hand      + hope it's OK \r
+5.  [ ] couldn't solder bottom pad of U5 by hand      + hope it's OK \r
                Attached to large gnd plane. Hard to solder. Designed for IR SMT \r
                assembly. Try large iron on vias from bottom. \r
 \r
-[ ] Can R6,R2,R5,R3,R4 be 10k to match R1? \r
+6.  [ ] Can R6,R2,R5,R3,R4 be 10k to match R1? \r
                Don't know if 10K will work for R6. Discovery has 680 or small value. \r
                Try it. Can't hurt. \r
                R2 & R5 Are I2C pins. Recommended 4.7K for max speed. Not used now on \r
@@ -34,45 +32,46 @@ Tuesday, July 07, 2014      04:05 PM
                R3 & R4 should work with 10K. \r
                Let me know results & I can change values if appropriate. \r
 \r
-[ ] Would VDDA power supply circuit be better located closer to U1? \r
-               I think they are pretty close now. I'll look at VDDA function and advise. \r
+7.  [X] Would VDDA power supply circuit be better located closer to U1? \r
+               Data sheet advises placing caps on opposite side of board, under VDDA pins. \r
+               Parts are place as close as possible, on same side of board. Return is low impedance plane and supply well bypassed. Unless this presents problems, I'd leave it. RGB 07/15/2014\r
 \r
-[ ] Larger TAPR/Credits text on bottom?      + there is plenty of room \r
-               Tried to get printing without visa & pads in the text. Smallest via has \r
-               .016" drill and is tented. I'll enlarge text & see what I can do. \r
+8.  [X] Larger TAPR/Credits text on bottom?      + there is plenty of room \r
+               Enlarged text from 1mm to 1.42mm. Text now extends almost all the way across PCB. RGB 07/15/2014\r
 \r
-[ ] What was Vin range meant to be? \r
+9.  [X] What was Vin range meant to be? \r
                VIN is 1 diode drop lower than VEXT(6-16VDC) or approx 5.5 - 15.5VDC Used to power LM386 to get more output swing.\r
 \r
-[ ] move R20 label close to R20     + I loaded R20 in the wrong place! \r
-               Will do. \r
-\r
-[X] is 4k7 missing from BOM or just my order?    + I didn't have any in my Digikey order \r
+10. [X] move R20 label close to R20     + I loaded R20 in the wrong place! \r
+               R20 designation moved adjacent to part. RGB 07/15/2014\r
+               \r
+11. [X] is 4k7 missing from BOM or just my order?    + I didn't have any in my Digikey order \r
                Part definition error. Part # in part definition field. Will correct database & BOM.\r
-               This affects R2,R3, R4, R5 & R48. Should be Vishay Dale # CRCW06034K70FKEA, Digikey # 541-4.70KHCT-ND, Part Def: RES 4.70K OHM 1/10W 1% 0603 SMD\r
-               07/08/2014 - RGB\r
-\r
-====================================\r
-Tuesday, July 08, 2014 10:54 AM\r
-====================================\r
+               This affects R2,R3, R4, R5 & R48. Should be Vishay Dale # CRCW06034K70FKEA, Digikey # 541-4.70KHCT-ND, Part Def: RES 4.70K OHM 1/10W 1% 0603 SMD  07/08/2014 - RGB\r
 \r
-[X] Re C26, could u pls align the BOM and sch?  I'm not sure which one has to change. \r
+12. [X] Re C26, could u pls align the BOM and sch?  I'm not sure which one has to change. \r
                C26 should be 25V to accommodate +16V power in max. \r
                OOPS! Found that C23, C26, C40 & C46 all should be 25V. That's why I made them separate line item. I'll Change BOM to Digikey part # 490-1524-6-ND Murata # GRM188R71E104KA01D\r
                07/08/2014 - Same as #2 above - RGB\r
                \r
-[ ] Re CN3, Hmm, now I'm not sure!  I dug around in the shed and found a connector that fits so I'm OK for now. \r
+13. [ ] Re CN3, Hmm, now I'm not sure!  I dug around in the shed and found a connector that fits so I'm OK for now. \r
                CN3 is Switchcraft RASM712PX   2.5mm ID, 5.5mm OD Plug.  CONN PWR PLUG DC 2.5X5.5 8A MOD Digikey  # CP3-002BH-ND\r
-               I've noted a problem, but will wait til you decide.\r
+               I've noted a problem, but will wait til you decide. RGB\r
 \r
-[ ] OK I just check the BOM I have, and there are no 4.7k resistors on it, e.g. R2, R3, R4, R5.  Oh OK, the BOM has a part number.  Not sure what that mapped to on my Digikey order, just noticed I didn't get any 4k7s.  Maybe change the BOM to indicate the part value? \r
+14. [ ] OK I just check the BOM I have, and there are no 4.7k resistors on it, e.g. R2, R3, R4, R5.  Oh OK, the BOM has a part number.  Not sure what that mapped to on my Digikey order, just noticed I didn't get any 4k7s.  Maybe change the BOM to indicate the part value? \r
                Part database  error, invalid part definition. Digikey & Vishay Dale part numbers are correct. Part definition for R2, R3, R4, R5 & R48 should be: RES 4.70K OHM 1/10W 1% 0603 SMD Will correct part database & BOM.\r
 \r
-====================================\r
+15. [X] CN7 3.5mm socket etc have two small plastic mounting lugs that require holes\r
+               CN7, CN8, CN9 & CN10 plastic tabs interfere with pads on top layer. Since the tabs are plastic and don't extend thru the PCB, I am approving these 4 discrepancies. RGB 07/15.2014              \r
+\r
+16. [X] Should R46 be described as a trimmer resistor (rather than POT?) on the BOM\r
+               R46 incorrectly specified on BOM. Corrected. Part s described as POT in DIGIKEY description. RGB 07/15/2014\r
+\r
+17. [X] Is label for R1 & R2 transposed? \r
+               Labels were transposed. Corrected. RGB 07/15/2014\r
+\r
+18. [ ] Add 100nF reset cap as per data sheet and discovery\r
 \r
-[ ] CN7 3.5mm socket etc have two small plastic mounting lugs that require holes\r
-[ ] Could C40 be rated at 16V?\r
-[ ] Should R46 be described as a trimmer resistor (rather than POT?) on the BOM\r
-[ ] Is label for R1 & R2 transposed?\r
-[ ] Add 100nF reset cap as per data sheet and discovery\r
-[ ] replace J7 & J2 with 0805 0 ohm Rs\r
+19. [X] replace J7 & J2 with 0805 0 ohm Rs\r
+                Jumpers were originally inserted to permit bringing up SM1000 and protecting circuitry from overvoltages and measuring currents. \r
+                Jumpers replaced with 0 OHM resistors. RGB 07/15/2014\r

diff --git a/smartmic/SM1000-REV-B2/SM1000-REV-B2.brd b/smartmic/SM1000-REV-B2/SM1000-REV-B2.brd
index 155c2e0067be6b4c2c0c5afdc19b1847d0caeb71..d8d700a0ce696af48e07b5574e249dc648bd0774 100644 (file)
--- a/smartmic/SM1000-REV-B2/SM1000-REV-B2.brd
+++ b/smartmic/SM1000-REV-B2/SM1000-REV-B2.brd
@@ -8,7 +8,7 @@
 </settings>
 <grid distance="0.5" unitdist="mm" unit="mm" style="dots" multiple="1" display="yes" altdistance="0.1" altunitdist="mm" altunit="mm"/>
 <layers>
-<layer number="1" name="Top" color="4" fill="1" visible="yes" active="yes"/>
+<layer number="1" name="Top" color="4" fill="1" visible="no" active="yes"/>
 <layer number="2" name="GND" color="3" fill="1" visible="no" active="yes"/>
 <layer number="3" name="Route3" color="4" fill="3" visible="no" active="no"/>
 <layer number="4" name="Route4" color="1" fill="4" visible="no" active="no"/>
@@ -23,17 +23,17 @@
 <layer number="13" name="Route13" color="4" fill="5" visible="no" active="no"/>
 <layer number="14" name="Route14" color="1" fill="6" visible="no" active="no"/>
 <layer number="15" name="VDD" color="6" fill="1" visible="no" active="yes"/>
-<layer number="16" name="Bottom" color="1" fill="1" visible="no" active="yes"/>
+<layer number="16" name="Bottom" color="1" fill="1" visible="yes" active="yes"/>
 <layer number="17" name="Pads" color="2" fill="1" visible="yes" active="yes"/>
 <layer number="18" name="Vias" color="2" fill="1" visible="yes" active="yes"/>
 <layer number="19" name="Unrouted" color="6" fill="1" visible="yes" active="yes"/>
 <layer number="20" name="Dimension" color="15" fill="1" visible="yes" active="yes"/>
-<layer number="21" name="tPlace" color="7" fill="1" visible="yes" active="yes"/>
-<layer number="22" name="bPlace" color="7" fill="1" visible="no" active="yes"/>
-<layer number="23" name="tOrigins" color="15" fill="1" visible="yes" active="yes"/>
-<layer number="24" name="bOrigins" color="15" fill="1" visible="no" active="yes"/>
-<layer number="25" name="tNames" color="7" fill="1" visible="yes" active="yes"/>
-<layer number="26" name="bNames" color="7" fill="1" visible="no" active="yes"/>
+<layer number="21" name="tPlace" color="7" fill="1" visible="no" active="yes"/>
+<layer number="22" name="bPlace" color="7" fill="1" visible="yes" active="yes"/>
+<layer number="23" name="tOrigins" color="15" fill="1" visible="no" active="yes"/>
+<layer number="24" name="bOrigins" color="15" fill="1" visible="yes" active="yes"/>
+<layer number="25" name="tNames" color="7" fill="1" visible="no" active="yes"/>
+<layer number="26" name="bNames" color="7" fill="1" visible="yes" active="yes"/>
 <layer number="27" name="tValues" color="7" fill="1" visible="no" active="yes"/>
 <layer number="28" name="bValues" color="7" fill="1" visible="no" active="yes"/>
 <layer number="29" name="tStop" color="7" fill="3" visible="no" active="yes"/>
@@ -370,15 +370,15 @@ CONNECTOR</text>
 <dimension x1="0" y1="0" x2="65" y2="0" x3="32.5" y3="-4.5" textsize="1.6764" textratio="10" layer="100" dtype="horizontal"/>
 <dimension x1="65" y1="0" x2="65" y2="90" x3="69" y3="45" textsize="1.778" textratio="10" layer="100" dtype="vertical"/>
 <text x="85" y="35.5" size="1.778" layer="144" ratio="10">SM1000-REV-B- DRILL TABLE</text>
-<text x="63.02" y="34.14" size="1" layer="22" ratio="10" rot="MR0">Copyright     2014
+<text x="62.77" y="46.59" size="1.4224" layer="22" font="vector" ratio="10" rot="MR0">Copyright   2014
 Richard Barnich and David Rowe
 Licensed under TAPR Open Hardware License</text>
-<text x="56.52" y="37.27" size="1.016" layer="22" ratio="15" rot="MR0">c</text>
-<circle x="56.12" y="37.64" radius="0.58309375" width="0.1" layer="22"/>
-<wire x1="63.5" y1="38.84" x2="30" y2="39" width="0.1" layer="22"/>
-<wire x1="30" y1="39" x2="30" y2="33.5" width="0.1" layer="22"/>
-<wire x1="30" y1="33.5" x2="63.5" y2="33.5" width="0.1" layer="22"/>
-<wire x1="63.5" y1="33.5" x2="63.5" y2="38.84" width="0.1" layer="22"/>
+<text x="51.12" y="51.07" size="1.4224" layer="22" ratio="15" rot="MR0">c</text>
+<circle x="50.57" y="51.59" radius="0.8" width="0.1" layer="22"/>
+<wire x1="64" y1="53.5" x2="9" y2="53.5" width="0.1" layer="22"/>
+<wire x1="9" y1="53.5" x2="9" y2="45.5" width="0.1" layer="22"/>
+<wire x1="9" y1="45.5" x2="64" y2="45.5" width="0.1" layer="22"/>
+<wire x1="64" y1="45.5" x2="64" y2="53.5" width="0.1" layer="22"/>
 <text x="1.5" y="81" size="0.8128" layer="1" font="vector" ratio="15">SM1000 Rev B1</text>
 <text x="1.5" y="82.5" size="0.8128" layer="21" ratio="15">SM1000 Rev B1</text>
 <wire x1="39.5" y1="62.9" x2="44" y2="62.9" width="0.2" layer="22"/>
@@ -1218,6 +1218,8 @@ Licensed under TAPR Open Hardware License</text>
 <text x="22.5" y="99.5" size="1.778" layer="203" ratio="10">16</text>
 <text x="41" y="105" size="1.778" layer="203" ratio="10">17</text>
 <text x="21" y="-39.5" size="1.778" layer="203" ratio="10">TOP DIMENSION</text>
+<dimension x1="0" y1="0" x2="6" y2="71" x3="-9.5" y3="35.5" textsize="1.778" textratio="10" layer="202" dtype="vertical"/>
+<dimension x1="65" y1="0" x2="55.43" y2="88.99" x3="71" y3="44.495" textsize="1.778" textratio="10" layer="202" dtype="vertical"/>
 </plain>
 <libraries>
 <library name="AA-IC">
@@ -1306,6 +1308,8 @@ Licensed under TAPR Open Hardware License</text>
 <wire x1="-9.9" y1="-3" x2="-9.9" y2="1.2" width="0" layer="39"/>
 <wire x1="-9.9" y1="1.2" x2="-5.9" y2="1.2" width="0" layer="39"/>
 <wire x1="-5.9" y1="1.2" x2="-5.9" y2="5.7" width="0" layer="39"/>
+<hole x="-2.5" y="0" drill="1.7"/>
+<hole x="4.5" y="0" drill="1.7"/>
 </package>
 <package name="SRN6045">
 <smd name="1" x="-2.15" y="0" dx="6" dy="2" layer="1" rot="R90"/>
@@ -1488,12 +1492,12 @@ INFINEON, www.infineon.com/cmc_upload/0/000/010/257/eh_db_5b.pdf</description>
 <text x="-5.5" y="6.5" size="1" layer="25" ratio="10">&gt;NAME</text>
 </package>
 <package name="SW-PWR">
-<pad name="1" x="2.5" y="-1.25" drill="0.5" shape="square"/>
-<pad name="2" x="0" y="-1.25" drill="0.5"/>
-<pad name="3" x="-2.5" y="-1.25" drill="0.5"/>
-<pad name="4" x="2.5" y="1.25" drill="0.5"/>
-<pad name="5" x="0" y="1.25" drill="0.5"/>
-<pad name="6" x="-2.5" y="1.25" drill="0.5"/>
+<pad name="1" x="2.5" y="-1.25" drill="1" diameter="1.778" shape="square"/>
+<pad name="2" x="0" y="-1.25" drill="1" diameter="1.778"/>
+<pad name="3" x="-2.5" y="-1.25" drill="1" diameter="1.778"/>
+<pad name="4" x="2.5" y="1.25" drill="1" diameter="1.778"/>
+<pad name="5" x="0" y="1.25" drill="1" diameter="1.778"/>
+<pad name="6" x="-2.5" y="1.25" drill="1" diameter="1.778"/>
 <wire x1="-4" y1="3" x2="5" y2="3" width="0.15" layer="21"/>
 <wire x1="-4.5" y1="-3" x2="5" y2="-3" width="0.15" layer="21"/>
 <wire x1="8.7" y1="3" x2="8.7" y2="-3" width="0.15" layer="21"/>
@@ -1691,6 +1695,22 @@ NS Package M08A</description>
 <text x="-2.5" y="6" size="1" layer="25" ratio="10">&gt;NAME</text>
 <circle x="0" y="0" radius="5.59016875" width="0.01" layer="39"/>
 </package>
+<package name="RR0805">
+<description>&lt;b&gt;RESISTOR&lt;/b&gt;&lt;p&gt;
+chip</description>
+<wire x1="-0.41" y1="0.635" x2="0.41" y2="0.635" width="0.1524" layer="51"/>
+<wire x1="-0.41" y1="-0.635" x2="0.41" y2="-0.635" width="0.1524" layer="51"/>
+<wire x1="-1.425" y1="0.95" x2="1.425" y2="0.95" width="0.0508" layer="39"/>
+<wire x1="1.425" y1="0.95" x2="1.425" y2="-0.95" width="0.0508" layer="39"/>
+<wire x1="1.425" y1="-0.95" x2="-1.425" y2="-0.95" width="0.0508" layer="39"/>
+<wire x1="-1.425" y1="-0.95" x2="-1.425" y2="0.95" width="0.0508" layer="39"/>
+<smd name="1" x="-0.95" y="0" dx="0.7" dy="1.3" layer="1" roundness="25"/>
+<smd name="2" x="0.95" y="0" dx="0.7" dy="1.3" layer="1" roundness="25"/>
+<text x="-1.462" y="1.116" size="1" layer="25" ratio="10">&gt;NAME</text>
+<rectangle x1="0.4064" y1="-0.6985" x2="1.0564" y2="0.7015" layer="51"/>
+<rectangle x1="-1.0668" y1="-0.6985" x2="-0.4168" y2="0.7015" layer="51"/>
+<rectangle x1="-0.1999" y1="-0.5001" x2="0.1999" y2="0.5001" layer="35"/>
+</package>
 </packages>
 </library>
 <library name="_Coherix">
@@ -2609,7 +2629,7 @@ design rules under a new name.</description>
 <attribute name="NAME" x="18.5" y="55" size="0.8128" layer="25" ratio="10" rot="R180"/>
 </element>
 <element name="R2" library="AA-ipc-7351-resistor" package="RESC1608X55N" value="4.7K,1%" x="15.5" y="64.5" locked="yes" smashed="yes">
-<attribute name="NAME" x="17.5" y="62.5" size="0.8128" layer="25"/>
+<attribute name="NAME" x="17.5" y="64.5" size="0.8128" layer="25"/>
 </element>
 <element name="R5" library="AA-ipc-7351-resistor" package="RESC1608X55N" value="4.7K,1%" x="15.5" y="60.5" locked="yes" smashed="yes">
 <attribute name="NAME" x="17.5" y="60.5" size="0.8128" layer="25"/>
@@ -2640,7 +2660,7 @@ design rules under a new name.</description>
 <attribute name="NAME" x="14.4" y="72.4" size="0.8128" layer="25"/>
 </element>
 <element name="R20" library="AA-ipc-7351-resistor" package="RESC1608X55N" value="22,1%" x="22.8" y="77.5" locked="yes" smashed="yes" rot="R90">
-<attribute name="NAME" x="25.5" y="80.3" size="0.8128" layer="25"/>
+<attribute name="NAME" x="22.7" y="80.5" size="0.8128" layer="25" rot="R90"/>
 </element>
 <element name="U2" library="_RoweTel" package="SOT23-5L" value="LD3985M33R" x="12.75" y="47.25" locked="yes" smashed="yes">
 <attribute name="NAME" x="11.25" y="49.45" size="0.8128" layer="25" ratio="10"/>
@@ -2671,10 +2691,6 @@ design rules under a new name.</description>
 <element name="R17" library="AA-ipc-7351-resistor" package="RESC1608X55N" value="1K,1%" x="18.75" y="44.5" locked="yes" smashed="yes" rot="R90">
 <attribute name="NAME" x="19.8" y="42.85" size="0.8128" layer="25" rot="R180"/>
 </element>
-<element name="J2" library="_Coherix" package="JMPR-2PIN" value="JMP-2PIN" x="23.75" y="46.25" locked="yes" smashed="yes">
-<attribute name="NAME" x="22.75" y="49.25" size="0.8128" layer="25"/>
-</element>
-<element name="SH2" library="_Coherix" package="NOPACKAGE" value="SHUNT,0.1IN" x="4.5" y="-0.5" locked="yes" smashed="yes" rot="R90"/>
 <element name="LED1" library="_RoweTel" package="LTST-S2200K" value="LED-RED,RA" x="29.3" y="88.5" smashed="yes" rot="R270">
 <attribute name="NAME" x="26.6" y="84.7" size="0.8128" layer="25"/>
 </element>
@@ -2718,7 +2734,7 @@ design rules under a new name.</description>
 <attribute name="NAME" x="18.5" y="82.85" size="0.8128" layer="25" rot="R180"/>
 </element>
 <element name="R26" library="AA-ipc-7351-resistor" package="RESC1608X55N" value="0 Ohm" x="24.5" y="81.5" smashed="yes" rot="R90">
-<attribute name="NAME" x="23.139" y="82.961" size="0.8128" layer="25" rot="R180"/>
+<attribute name="NAME" x="25.361" y="80.539" size="0.8128" layer="25"/>
 </element>
 <element name="C9" library="_RoweTel" package="C1206-TANT" value="4.7uF,16V,TANT" x="30.75" y="82.35" locked="yes" smashed="yes" rot="R270">
 <attribute name="NAME" x="31.95" y="82.55" size="0.8128" layer="25" ratio="10"/>
@@ -2804,7 +2820,7 @@ design rules under a new name.</description>
 <attribute name="VALUE" x="28.125" y="17.52" size="1.27" layer="27" ratio="10" rot="R90"/>
 <attribute name="NAME" x="21.443" y="20.956" size="0.8128" layer="25" ratio="10" rot="R180"/>
 </element>
-<element name="LD2" library="_RoweTel" package="SMD4" value="LTV-817S" x="52" y="23" locked="yes" smashed="yes" rot="R270">
+<element name="LD2" library="_RoweTel" package="SMD4" value="LTV-817S" x="52" y="23" smashed="yes" rot="R270">
 <attribute name="NAME" x="53.6" y="20.3" size="0.8128" layer="25" ratio="10" rot="R180"/>
 </element>
 <element name="R51" library="AA-ipc-7351-resistor" package="RESC1608X55N" value="390,1%" x="50.5" y="27.5" locked="yes" smashed="yes">
@@ -2884,11 +2900,11 @@ design rules under a new name.</description>
 <attribute name="NAME" x="58.35" y="68.95" size="0.8128" layer="25" ratio="10" rot="R180"/>
 <attribute name="VALUE" x="56.9625" y="72" size="1" layer="27" font="vector" ratio="10" rot="R270"/>
 </element>
-<element name="FB1" library="_RoweTel" package="FE0805" value="FB0805" x="45.5" y="23" locked="yes" smashed="yes" rot="R90">
-<attribute name="NAME" x="44.5" y="20" size="0.8128" layer="25" ratio="10"/>
+<element name="FB1" library="_RoweTel" package="FE0805" value="FB0805" x="45.5" y="23.5" smashed="yes" rot="R90">
+<attribute name="NAME" x="44.5" y="20.5" size="0.8128" layer="25" ratio="10"/>
 </element>
-<element name="FB2" library="_RoweTel" package="FE0805" value="FB0805" x="42.5" y="21.5" locked="yes" smashed="yes" rot="R270">
-<attribute name="NAME" x="41.2" y="22.2" size="0.8128" layer="25" ratio="10" rot="R90"/>
+<element name="FB2" library="_RoweTel" package="FE0805" value="FB0805" x="42.5" y="23.5" smashed="yes" rot="R270">
+<attribute name="NAME" x="41.2" y="24.2" size="0.8128" layer="25" ratio="10" rot="R90"/>
 </element>
 <element name="FB3" library="_RoweTel" package="FE0805" value="FB0805" x="34.5" y="30" locked="yes" smashed="yes" rot="R270">
 <attribute name="NAME" x="31" y="29.5" size="0.8128" layer="25" ratio="10"/>
@@ -2896,8 +2912,8 @@ design rules under a new name.</description>
 <element name="FB4" library="_RoweTel" package="FE0805" value="FB0805" x="40.5" y="35.5" smashed="yes" rot="R90">
 <attribute name="NAME" x="37.25" y="34" size="0.8128" layer="25" ratio="10"/>
 </element>
-<element name="FB6" library="_RoweTel" package="FE0805" value="FB0805" x="39" y="21.5" locked="yes" smashed="yes" rot="R270">
-<attribute name="NAME" x="41" y="19.5" size="0.8128" layer="25" ratio="10" rot="R90"/>
+<element name="FB6" library="_RoweTel" package="FE0805" value="FB0805" x="38.5" y="23" smashed="yes" rot="R270">
+<attribute name="NAME" x="40.5" y="21" size="0.8128" layer="25" ratio="10" rot="R90"/>
 </element>
 <element name="C43" library="AA-ipc-7351-capacitor" package="CAPC1608X92N" value="100pF,50V" x="21" y="29.5" locked="yes" smashed="yes" rot="R90">
 <attribute name="NAME" x="21.25" y="27.8325" size="0.8128" layer="25" ratio="10" rot="R180"/>
@@ -2914,11 +2930,11 @@ design rules under a new name.</description>
 <element name="U8" library="_RoweTel" package="SO08" value="LM386M-1" x="49.5" y="74.25" locked="yes" smashed="yes">
 <attribute name="NAME" x="46" y="72.5" size="0.8128" layer="25" rot="R90"/>
 </element>
-<element name="T1" library="_RoweTel" package="SM-LP-5001" value="SM-LP-5001" x="42.5" y="10" locked="yes" smashed="yes" rot="R270">
-<attribute name="NAME" x="46.5" y="18.5" size="0.8128" layer="25" ratio="10"/>
+<element name="T1" library="_RoweTel" package="SM-LP-5001" value="SM-LP-5001" x="42.5" y="12" smashed="yes" rot="R270">
+<attribute name="NAME" x="46.5" y="20.5" size="0.8128" layer="25" ratio="10"/>
 </element>
-<element name="T2" library="_RoweTel" package="SM-LP-5001" value="SM-LP-5001" x="54.5" y="10" locked="yes" smashed="yes" rot="R270">
-<attribute name="NAME" x="49.5" y="18.5" size="0.8128" layer="25" ratio="10"/>
+<element name="T2" library="_RoweTel" package="SM-LP-5001" value="SM-LP-5001" x="54.5" y="12" smashed="yes" rot="R270">
+<attribute name="NAME" x="49.5" y="20.5" size="0.8128" layer="25" ratio="10"/>
 </element>
 <element name="C46" library="ipc-7351-capacitor" package="CAPC1608X92N" value="100nF,25V" x="7.05" y="40.25" smashed="yes" rot="R270">
 <attribute name="NAME" x="8.41" y="40.44" size="0.8128" layer="25" ratio="10"/>
@@ -2989,10 +3005,6 @@ design rules under a new name.</description>
 <attribute name="NAME" x="37.3" y="67.3" size="0.8128" layer="25" font="vector" ratio="10"/>
 <attribute name="VALUE" x="39.9625" y="67.25" size="1" layer="27" font="vector" ratio="10" rot="R270"/>
 </element>
-<element name="J7" library="_Coherix" package="JMPR-2PIN" value="JMP-2PIN" x="3" y="53.5" locked="yes" smashed="yes" rot="R180">
-<attribute name="NAME" x="2.71" y="56.39" size="0.8128" layer="25"/>
-</element>
-<element name="SH6" library="_Coherix" package="NOPACKAGE" value="SHUNT,0.1IN" x="0.5" y="-0.5" locked="yes" smashed="yes"/>
 <element name="C52" library="AA-ipc-7351-capacitor" package="CAPC1608X92N" value="100nF,16V" x="37" y="73.25" locked="yes" smashed="yes">
 <attribute name="NAME" x="37.3" y="71.2" size="0.8128" layer="25" ratio="10" rot="R270"/>
 <attribute name="VALUE" x="35.75" y="71.2125" size="1" layer="27" font="vector" ratio="10"/>
@@ -3008,7 +3020,7 @@ design rules under a new name.</description>
 <attribute name="NAME" x="1.2" y="63.8" size="0.8128" layer="25" ratio="10"/>
 </element>
 <element name="R1" library="AA-ipc-7351-resistor" package="RESC1608X55N" value="10K,1%" x="15.5" y="62.5" locked="yes" smashed="yes">
-<attribute name="NAME" x="17.5" y="64.5" size="0.8128" layer="25"/>
+<attribute name="NAME" x="17.5" y="62.5" size="0.8128" layer="25"/>
 </element>
 <element name="J5" library="_Coherix" package="JMPR-2PIN" value="JMP-2PIN" x="16.75" y="67" locked="yes" smashed="yes" rot="R90">
 <attribute name="NAME" x="15.64" y="69.51" size="0.8128" layer="25" rot="R180"/>
@@ -3083,11 +3095,11 @@ design rules under a new name.</description>
 <element name="P16" library="_Coherix" package="TPAD50" value="TPAD50" x="62.5" y="84" smashed="yes">
 <attribute name="NAME" x="61.59" y="85.12" size="0.8128" layer="25"/>
 </element>
-<element name="P17" library="_Coherix" package="TPAD50" value="TPAD50" x="61.5" y="7" smashed="yes">
-<attribute name="NAME" x="60.64" y="8.09" size="0.8128" layer="25"/>
+<element name="P17" library="_Coherix" package="TPAD50" value="TPAD50" x="63" y="6" smashed="yes">
+<attribute name="NAME" x="62.14" y="7.09" size="0.8128" layer="25"/>
 </element>
-<element name="P18" library="_Coherix" package="TPAD50" value="TPAD50" x="61.5" y="4" smashed="yes">
-<attribute name="NAME" x="60.56" y="5.09" size="0.8128" layer="25"/>
+<element name="P18" library="_Coherix" package="TPAD50" value="TPAD50" x="63" y="1.8" smashed="yes">
+<attribute name="NAME" x="62.06" y="2.89" size="0.8128" layer="25"/>
 </element>
 <element name="P19" library="_Coherix" package="TPAD50" value="TPAD50" x="27.77" y="43.51" smashed="yes">
 <attribute name="NAME" x="29.13" y="44.19" size="0.8128" layer="25"/>
@@ -3112,6 +3124,8 @@ design rules under a new name.</description>
 <attribute name="VALUE" x="42.5875" y="38.25" size="1" layer="27" font="vector" ratio="10" rot="R90"/>
 </element>
 <element name="DRILEGEND" library="drilegend" package="DRILEGEND" value="" x="78.766053125" y="28.843325"/>
+<element name="R18" library="_RoweTel" package="RR0805" value="0 Ohm" x="-6" y="45" rot="R270"/>
+<element name="R21" library="_RoweTel" package="RR0805" value="0 Ohm" x="-6" y="51" rot="R270"/>
 </elements>
 <signals>
 <signal name="N$2">
@@ -3170,7 +3184,6 @@ design rules under a new name.</description>
 <contactref element="U1" pad="100"/>
 <contactref element="U1" pad="28"/>
 <contactref element="U1" pad="50"/>
-<contactref element="J2" pad="2"/>
 <contactref element="R4" pad="1"/>
 <contactref element="R51" pad="2"/>
 <contactref element="R44" pad="2"/>
@@ -3324,7 +3337,7 @@ design rules under a new name.</description>
 <contactref element="P13" pad="1"/>
 <contactref element="P15" pad="1"/>
 <contactref element="P17" pad="1"/>
-<wire x1="61.5" y1="7" x2="61.5" y2="10" width="0.4" layer="15"/>
+<wire x1="63" y1="6" x2="61.5" y2="10" width="0.4" layer="15"/>
 <wire x1="21.2" y1="73.2" x2="21.3" y2="73.2" width="0.4" layer="1"/>
 <wire x1="21.3" y1="73.2" x2="21.5" y2="73" width="0.4" layer="1"/>
 <contactref element="SW2" pad="3"/>
@@ -3351,6 +3364,45 @@ design rules under a new name.</description>
 <wire x1="37.25" y1="60.75" x2="37.5" y2="60.5" width="0.25" layer="1"/>
 <wire x1="37.5" y1="60.5" x2="37.8" y2="60.2" width="0.25" layer="1"/>
 <wire x1="37.8" y1="60.2" x2="37.8" y2="59.5" width="0.25" layer="1"/>
+<wire x1="55.88" y1="12.7" x2="60.46" y2="8.12" width="0.2" layer="2"/>
+<wire x1="55.88" y1="16.51" x2="55.88" y2="12.7" width="0.2" layer="2"/>
+<wire x1="35.56" y1="36.83" x2="55.88" y2="16.51" width="0.2" layer="2"/>
+<wire x1="35.56" y1="38.1" x2="35.56" y2="36.83" width="0.2" layer="2"/>
+<wire x1="29.21" y1="44.45" x2="35.56" y2="38.1" width="0.2" layer="2"/>
+<wire x1="24.13" y1="44.45" x2="29.21" y2="44.45" width="0.2" layer="2"/>
+<wire x1="60.46" y1="8.12" x2="60.58" y2="8" width="0.2" layer="2"/>
+<wire x1="60.58" y1="8" x2="63" y2="6" width="0.2" layer="2"/>
+<contactref element="R18" pad="2"/>
+<wire x1="55.5" y1="74.5" x2="62.5" y2="87" width="0" layer="19" extent="1-1"/>
+<wire x1="59" y1="71.55" x2="55.5" y2="72.7" width="0" layer="19" extent="1-1"/>
+<wire x1="60.5" y1="65.45" x2="60" y2="68.5" width="0" layer="19" extent="1-1"/>
+<wire x1="55.5" y1="65.45" x2="60.5" y2="65.45" width="0" layer="19" extent="1-1"/>
+<wire x1="46" y1="64.75" x2="52" y2="64.3" width="0" layer="19" extent="1-1"/>
+<wire x1="43.1" y1="61.8" x2="46" y2="63.5" width="0" layer="19" extent="1-1"/>
+<wire x1="37.8" y1="60.2" x2="40.4" y2="61.8" width="0" layer="19" extent="1-1"/>
+<wire x1="31.5" y1="59.1" x2="36" y2="60.75" width="0" layer="19" extent="1-1"/>
+<wire x1="22" y1="56.5" x2="27.5" y2="58.25" width="0" layer="19" extent="1-1"/>
+<wire x1="22.5" y1="52" x2="21.75" y2="56.25" width="0" layer="19" extent="1-1"/>
+<wire x1="14.7" y1="58.5" x2="20.8" y2="58.8" width="0" layer="19" extent="1-1"/>
+<wire x1="14.7" y1="60.5" x2="14.7" y2="58.5" width="0" layer="19" extent="1-1"/>
+<wire x1="13.5" y1="64.5" x2="13.5" y2="60.5" width="0" layer="19" extent="1-1"/>
+<wire x1="7.5" y1="62.5" x2="13.5" y2="60.5" width="0" layer="19" extent="1-1"/>
+<wire x1="24.13" y1="44.45" x2="22.2" y2="51.7" width="0" layer="19" extent="1-2"/>
+<wire x1="51.77" y1="55.75" x2="52" y2="64.3" width="0" layer="19" extent="1-1"/>
+<wire x1="53.5" y1="50.7" x2="51.77" y2="55.75" width="0" layer="19" extent="1-1"/>
+<wire x1="52.5" y1="46.95" x2="54" y2="49.5" width="0" layer="19" extent="1-1"/>
+<wire x1="49.5" y1="46.95" x2="52.5" y2="46.95" width="0" layer="19" extent="1-1"/>
+<wire x1="46.5" y1="46.95" x2="49.5" y2="46.95" width="0" layer="19" extent="1-1"/>
+<wire x1="45" y1="46" x2="46.5" y2="45.5" width="0" layer="19" extent="1-1"/>
+<wire x1="18.25" y1="73.2" x2="14.7" y2="64.5" width="0" layer="19" extent="1-1"/>
+<wire x1="19.4" y1="78.3" x2="20.25" y2="73.2" width="0" layer="19" extent="1-1"/>
+<wire x1="19.23" y1="86.34" x2="19.5" y2="80.7" width="0" layer="19" extent="1-16"/>
+<wire x1="12.73" y1="86.34" x2="17" y2="86.5" width="0" layer="19" extent="16-16"/>
+<wire x1="3" y1="85.5" x2="11.4" y2="86.1" width="0" layer="19" extent="16-16"/>
+<wire x1="32" y1="78.3" x2="22.5" y2="73.25" width="0" layer="19" extent="1-1"/>
+<wire x1="36" y1="76.5" x2="33.35" y2="76.6" width="0" layer="19" extent="1-1"/>
+<wire x1="51.3" y1="27.5" x2="55.88" y2="16.51" width="0" layer="19" extent="1-2"/>
+<wire x1="-6" y1="44.05" x2="55.88" y2="12.7" width="0" layer="19" extent="1-2"/>
 </signal>
 <signal name="BOOT1">
 <contactref element="R6" pad="2"/>
@@ -3465,20 +3517,7 @@ design rules under a new name.</description>
 <wire x1="10.74" y1="6.26" x2="11" y2="6" width="1.27" layer="1"/>
 <wire x1="16.36" y1="6.26" x2="11.26" y2="6.26" width="1.27" layer="1"/>
 <wire x1="11.26" y1="6.26" x2="11" y2="6" width="1.27" layer="1"/>
-<wire x1="21.4" y1="2.4" x2="12.4" y2="2.4" width="1.27" layer="16"/>
-<wire x1="21.4" y1="2.4" x2="26" y2="2.4" width="1.27" layer="16"/>
-<wire x1="26" y1="2.4" x2="26" y2="2.5" width="1.27" layer="16"/>
-<wire x1="26" y1="2.5" x2="26.1" y2="2.4" width="1.27" layer="16"/>
-<wire x1="26.1" y1="2.4" x2="30.4" y2="2.4" width="1.27" layer="16"/>
 <contactref element="C48" pad="2"/>
-<wire x1="48.5" y1="20" x2="50.5" y2="20" width="0.2" layer="1"/>
-<wire x1="50.5" y1="20" x2="52" y2="18.5" width="0.2" layer="1"/>
-<wire x1="52" y1="16.29" x2="52" y2="18.5" width="0.2" layer="1"/>
-<wire x1="52" y1="16.29" x2="51.96" y2="16.25" width="0.2" layer="1"/>
-<wire x1="39.96" y1="16.25" x2="39.96" y2="17.46" width="0.2" layer="1"/>
-<wire x1="39.96" y1="17.46" x2="41" y2="18.5" width="0.2" layer="1"/>
-<via x="41" y="18.5" extent="1-16" drill="0.4"/>
-<via x="48.5" y="20" extent="1-16" drill="0.4"/>
 <wire x1="34" y1="87.5" x2="35.5" y2="87.5" width="0.6" layer="16"/>
 <wire x1="35.5" y1="87.5" x2="36.5" y2="88.5" width="0.6" layer="16"/>
 <via x="36.5" y="88.5" extent="1-16" drill="0.6" diameter="1.27"/>
@@ -3726,10 +3765,6 @@ design rules under a new name.</description>
 <contactref element="R52" pad="1"/>
 <wire x1="54.3" y1="52.3" x2="56.46" y2="54.46" width="0.2" layer="1"/>
 <wire x1="41.35" y1="69.85" x2="41.3" y2="69.85" width="0.2" layer="1"/>
-<wire x1="41" y1="18.5" x2="41.5" y2="19" width="0.2" layer="16"/>
-<wire x1="41.5" y1="19" x2="44.1" y2="19" width="0.2" layer="16"/>
-<wire x1="44.1" y1="19" x2="45.1" y2="20" width="0.2" layer="16"/>
-<wire x1="45.1" y1="20" x2="48.5" y2="20" width="0.2" layer="16"/>
 <polygon width="0.2" layer="2" isolate="0.3">
 <vertex x="46.5" y="89"/>
 <vertex x="64" y="89"/>
@@ -3751,8 +3786,8 @@ design rules under a new name.</description>
 <contactref element="P14" pad="1"/>
 <contactref element="P16" pad="1"/>
 <contactref element="P18" pad="1"/>
-<wire x1="61.5" y1="4" x2="63.5" y2="6" width="0.4" layer="2"/>
-<wire x1="63.5" y1="6" x2="63.5" y2="10" width="0.4" layer="2"/>
+<wire x1="63" y1="1.8" x2="63.5" y2="7" width="0.4" layer="2"/>
+<wire x1="63.5" y1="7" x2="63.5" y2="10.5" width="0.4" layer="2"/>
 <contactref element="C1" pad="1"/>
 <contactref element="C30" pad="2"/>
 <wire x1="3" y1="10.7" x2="3" y2="6.33" width="0.5" layer="1"/>
@@ -3772,6 +3807,21 @@ design rules under a new name.</description>
 <wire x1="40.3" y1="65.25" x2="40.3" y2="64.9" width="0.2" layer="1"/>
 <wire x1="40.3" y1="64.9" x2="40.3" y2="64.1" width="0.2" layer="1"/>
 <wire x1="40.4" y1="59.8" x2="43.1" y2="59.8" width="1" layer="16"/>
+<wire x1="12.4" y1="2.4" x2="12.4" y2="4.4" width="1.27" layer="16"/>
+<wire x1="12.4" y1="4.4" x2="14" y2="6" width="1.27" layer="16"/>
+<wire x1="14" y1="6" x2="20.5" y2="6" width="1.27" layer="16"/>
+<wire x1="20.5" y1="6" x2="21.5" y2="5" width="1.27" layer="16"/>
+<wire x1="21.5" y1="2.5" x2="21.4" y2="2.4" width="1.27" layer="16"/>
+<wire x1="21.5" y1="5" x2="23" y2="6.5" width="1.27" layer="16"/>
+<wire x1="23" y1="6.5" x2="27.5" y2="6.5" width="1.27" layer="16"/>
+<wire x1="27.5" y1="6.5" x2="29" y2="6.5" width="1.27" layer="16"/>
+<wire x1="29" y1="6.5" x2="30.5" y2="5" width="1.27" layer="16"/>
+<wire x1="30.5" y1="5" x2="30.5" y2="2.5" width="1.27" layer="16"/>
+<wire x1="30.5" y1="2.5" x2="30.4" y2="2.4" width="1.27" layer="16"/>
+<wire x1="21.5" y1="5" x2="21.5" y2="2.5" width="1.27" layer="16"/>
+<wire x1="21.5" y1="2.5" x2="21.4" y2="2.4" width="1.27" layer="16"/>
+<wire x1="39.96" y1="18.25" x2="51.96" y2="18.25" width="0" layer="19" extent="1-1"/>
+<wire x1="63.5" y1="10.5" x2="51.96" y2="18.25" width="0" layer="19" extent="1-2"/>
 </signal>
 <signal name="SCL">
 <contactref element="U1" pad="92"/>
@@ -3927,18 +3977,15 @@ design rules under a new name.</description>
 <wire x1="35.7" y1="58.1" x2="39.7" y2="58.1" width="0.2" layer="16"/>
 </signal>
 <signal name="+3.3V">
-<contactref element="J2" pad="1"/>
 <contactref element="U2" pad="5"/>
 <contactref element="C4" pad="1"/>
 <contactref element="C5" pad="1"/>
 <contactref element="R17" pad="2"/>
-<wire x1="23.75" y1="47.52" x2="23.75" y2="48.55" width="0.4" layer="1"/>
 <wire x1="23.75" y1="48.55" x2="21.25" y2="48.55" width="0.4" layer="1"/>
 <wire x1="18.75" y1="48.55" x2="21.25" y2="48.55" width="0.4" layer="1"/>
 <wire x1="18.75" y1="45.3" x2="19.2" y2="45.3" width="0.2" layer="1"/>
 <wire x1="22.5" y1="45" x2="22.5" y2="47" width="0.2" layer="1"/>
 <wire x1="22.5" y1="47" x2="23.02" y2="47.52" width="0.2" layer="1"/>
-<wire x1="23.02" y1="47.52" x2="23.75" y2="47.52" width="0.2" layer="1"/>
 <wire x1="13.7" y1="46.1" x2="14.6" y2="46.1" width="0.4" layer="1"/>
 <wire x1="14.6" y1="46.1" x2="15" y2="46.5" width="0.4" layer="1"/>
 <wire x1="15" y1="46.5" x2="17.05" y2="48.55" width="0.4" layer="1"/>
@@ -3951,6 +3998,9 @@ design rules under a new name.</description>
 <wire x1="20.5" y1="44" x2="22" y2="44" width="0.2" layer="1"/>
 <wire x1="22" y1="44" x2="22.5" y2="44.5" width="0.2" layer="1"/>
 <wire x1="22.5" y1="44.5" x2="22.5" y2="45" width="0.2" layer="1"/>
+<contactref element="R18" pad="1"/>
+<wire x1="13.7" y1="46.1" x2="-6" y2="45.95" width="0" layer="19" extent="1-1"/>
+<wire x1="23.02" y1="47.52" x2="23.75" y2="48.55" width="0" layer="19" extent="1-1"/>
 </signal>
 <signal name="+5V">
 <contactref element="U2" pad="1"/>
@@ -4487,12 +4537,6 @@ design rules under a new name.</description>
 <contactref element="U1" pad="57"/>
 <contactref element="LD2" pad="2"/>
 <wire x1="31.5" y1="73.25" x2="31.5" y2="70" width="0.2" layer="1"/>
-<wire x1="49" y1="21.73" x2="48.27" y2="21.73" width="0.2" layer="1"/>
-<wire x1="48.27" y1="21.73" x2="48" y2="22" width="0.2" layer="1"/>
-<wire x1="48" y1="22" x2="48" y2="25.5" width="0.2" layer="1"/>
-<wire x1="48" y1="25.5" x2="48.5" y2="26" width="0.2" layer="1"/>
-<wire x1="48.5" y1="26" x2="48.5" y2="29" width="0.2" layer="1"/>
-<wire x1="48.5" y1="29" x2="46" y2="31.5" width="0.2" layer="1"/>
 <wire x1="43.5" y1="33" x2="43.5" y2="43" width="0.2" layer="1"/>
 <via x="43.5" y="43" extent="1-16" drill="0.4"/>
 <wire x1="31.5" y1="70" x2="31.5" y2="66.5" width="0.2" layer="1"/>
@@ -4521,6 +4565,7 @@ design rules under a new name.</description>
 <wire x1="45.3" y1="57.8" x2="45.3" y2="59.7" width="0.2" layer="1"/>
 <wire x1="45.3" y1="59.7" x2="45.3" y2="61.8" width="0.2" layer="1"/>
 <wire x1="45.3" y1="61.8" x2="43" y2="64.1" width="0.2" layer="1"/>
+<wire x1="49" y1="21.73" x2="46" y2="31.5" width="0" layer="19" extent="1-1"/>
 </signal>
 <signal name="!TEST!">
 <contactref element="R4" pad="2"/>
@@ -4721,25 +4766,24 @@ design rules under a new name.</description>
 <contactref element="R34" pad="1"/>
 <contactref element="C25" pad="1"/>
 <contactref element="C46" pad="1"/>
-<contactref element="J7" pad="1"/>
 <wire x1="13.125" y1="39.635" x2="11.365" y2="39.635" width="0.5" layer="1"/>
 <wire x1="11.365" y1="39.635" x2="11" y2="40" width="0.5" layer="1"/>
-<wire x1="3" y1="52.23" x2="1.2" y2="50.43" width="0.5" layer="15"/>
-<wire x1="1.2" y1="50.43" x2="1.2" y2="44.55" width="0.5" layer="15"/>
-<wire x1="1.2" y1="44.55" x2="2.5" y2="44.55" width="0.5" layer="15"/>
-<wire x1="2.5" y1="44.55" x2="2.5" y2="44.7" width="0.5" layer="15"/>
-<via x="2.5" y="44.7" extent="1-16" drill="0.4"/>
-<wire x1="2.5" y1="44.7" x2="2.5" y2="43" width="0.5" layer="1"/>
 <contactref element="C1" pad="2"/>
-<wire x1="4.93" y1="54.16" x2="3" y2="52.23" width="0.4" layer="16"/>
 <wire x1="46.5" y1="57" x2="46.9" y2="57.4" width="0.4" layer="16"/>
 <wire x1="46.9" y1="57.4" x2="46.9" y2="58.4" width="0.4" layer="16"/>
 <wire x1="46.9" y1="58.4" x2="46.9" y2="59.9" width="0.4" layer="16"/>
 <wire x1="46.9" y1="59.9" x2="47.5" y2="60.5" width="0.4" layer="16"/>
-<wire x1="3" y1="52.23" x2="4.63" y2="50.6" width="0.4" layer="16"/>
 <wire x1="4.63" y1="50.6" x2="22.9" y2="50.6" width="0.4" layer="16"/>
 <wire x1="22.9" y1="50.6" x2="24.8" y2="52.5" width="0.4" layer="16"/>
 <wire x1="24.8" y1="52.5" x2="26" y2="52.5" width="0.4" layer="16"/>
+<contactref element="R21" pad="2"/>
+<wire x1="1.9" y1="41.1" x2="-6" y2="50.05" width="0" layer="19" extent="1-1"/>
+<wire x1="4.5" y1="41.5" x2="1.9" y2="41.1" width="0" layer="19" extent="1-1"/>
+<wire x1="5.55" y1="43.4" x2="4.5" y2="41.5" width="0" layer="19" extent="1-1"/>
+<wire x1="7.05" y1="41.05" x2="4.5" y2="41.5" width="0" layer="19" extent="1-1"/>
+<wire x1="11" y1="40" x2="7.05" y2="41.05" width="0" layer="19" extent="1-1"/>
+<wire x1="4.63" y1="50.6" x2="5.55" y2="43.4" width="0" layer="19" extent="1-16"/>
+<wire x1="4.93" y1="54.16" x2="4.63" y2="50.6" width="0" layer="19" extent="16-16"/>
 </signal>
 <signal name="N$43">
 <contactref element="R50" pad="1"/>
@@ -4861,17 +4905,6 @@ design rules under a new name.</description>
 <contactref element="CN7" pad="10"/>
 <contactref element="CN12" pad="15"/>
 <contactref element="C44" pad="1"/>
-<wire x1="52.75" y1="15.8" x2="52.75" y2="10.75" width="0.2" layer="16"/>
-<wire x1="52.75" y1="10.75" x2="51" y2="9" width="0.2" layer="16"/>
-<wire x1="51" y1="9" x2="37.2" y2="9" width="0.2" layer="16"/>
-<wire x1="37.2" y1="9" x2="37.1" y2="9" width="0.2" layer="16"/>
-<wire x1="37.1" y1="9" x2="36.6" y2="9.5" width="0.2" layer="16"/>
-<wire x1="36.6" y1="9.5" x2="35.9" y2="9.5" width="0.2" layer="16"/>
-<wire x1="35.9" y1="9.5" x2="35.4" y2="9" width="0.2" layer="16"/>
-<wire x1="35.4" y1="9" x2="28" y2="9" width="0.2" layer="16"/>
-<wire x1="28" y1="9" x2="26.5" y2="10.5" width="0.2" layer="16"/>
-<wire x1="24" y1="11" x2="23.5" y2="10.5" width="0.2" layer="16"/>
-<wire x1="23.5" y1="10.5" x2="23" y2="10" width="0.2" layer="16"/>
 <wire x1="23" y1="10" x2="18.5" y2="10" width="0.2" layer="16"/>
 <wire x1="18.5" y1="10" x2="18" y2="10.5" width="0.2" layer="16"/>
 <via x="18" y="10.5" extent="1-16" drill="0.4"/>
@@ -4889,35 +4922,34 @@ design rules under a new name.</description>
 <wire x1="18" y1="26.85" x2="18" y2="26.8" width="0.2" layer="1"/>
 <wire x1="20.1" y1="25.9" x2="20.05" y2="25.9" width="0.2" layer="16"/>
 <wire x1="20.05" y1="25.9" x2="18.55" y2="27.4" width="0.2" layer="16"/>
-<wire x1="24" y1="11" x2="24.25" y2="11.25" width="0.2" layer="16"/>
-<wire x1="24.25" y1="11.25" x2="25.7" y2="11.25" width="0.2" layer="16"/>
-<wire x1="25.7" y1="11.25" x2="25.75" y2="11.25" width="0.2" layer="16"/>
-<wire x1="25.75" y1="11.25" x2="26.5" y2="10.5" width="0.2" layer="16"/>
 <wire x1="21" y1="25.9" x2="21.46" y2="25.9" width="0.2" layer="16"/>
 <wire x1="21.46" y1="25.9" x2="22.49" y2="24.87" width="0.2" layer="16"/>
 <wire x1="22.49" y1="24.87" x2="23.5" y2="25.88" width="0.2" layer="1"/>
 <wire x1="23.5" y1="25.88" x2="23.5" y2="26.37" width="0.2" layer="1"/>
+<via x="54.61" y="13.97" extent="1-16" drill="0.4"/>
+<wire x1="23" y1="10" x2="24" y2="9" width="0.2" layer="16"/>
+<wire x1="24" y1="9" x2="27.5" y2="9" width="0.2" layer="16"/>
+<wire x1="27.5" y1="9" x2="28" y2="8.5" width="0.2" layer="16"/>
+<wire x1="28" y1="8.5" x2="35.5" y2="8.5" width="0.2" layer="16"/>
+<wire x1="35.5" y1="8.5" x2="36" y2="9" width="0.2" layer="16"/>
+<wire x1="36" y1="9" x2="41" y2="9" width="0.2" layer="16"/>
+<wire x1="41" y1="9" x2="41.5" y2="8.5" width="0.2" layer="16"/>
+<wire x1="52.75" y1="15.8" x2="52.78" y2="15.8" width="0.2" layer="16"/>
+<wire x1="52.78" y1="15.8" x2="54.61" y2="13.97" width="0.2" layer="16"/>
+<wire x1="41.5" y1="8.5" x2="52.5" y2="8.5" width="0.2" layer="16"/>
+<wire x1="52.5" y1="8.5" x2="54.5" y2="10.5" width="0.2" layer="16"/>
+<wire x1="54.5" y1="10.5" x2="54.61" y2="10.61" width="0.2" layer="16"/>
+<wire x1="54.61" y1="10.61" x2="54.61" y2="13.97" width="0.2" layer="16"/>
 </signal>
 <signal name="SPKR">
 <contactref element="CN6" pad="10"/>
 <contactref element="CN12" pad="16"/>
 <contactref element="C43" pad="1"/>
-<wire x1="61.75" y1="15.8" x2="61.75" y2="10.25" width="0.2" layer="16"/>
-<wire x1="61.75" y1="10.25" x2="60" y2="8.5" width="0.2" layer="16"/>
 <wire x1="19.5" y1="23.88" x2="19.5" y2="23.87" width="0.2" layer="1"/>
 <wire x1="19.5" y1="23.87" x2="19.5" y2="21.7" width="0.2" layer="1"/>
 <wire x1="19.5" y1="21.7" x2="22" y2="19.2" width="0.2" layer="1"/>
 <wire x1="22" y1="19.2" x2="22" y2="15.5" width="0.2" layer="1"/>
-<wire x1="22" y1="15.5" x2="23.5" y2="14" width="0.2" layer="1"/>
-<via x="25" y="10.5" extent="1-16" drill="0.4"/>
-<wire x1="27" y1="8.5" x2="35.6" y2="8.5" width="0.2" layer="16"/>
-<wire x1="35.6" y1="8.5" x2="36" y2="8.9" width="0.2" layer="16"/>
-<wire x1="36" y1="8.9" x2="36.5" y2="8.9" width="0.2" layer="16"/>
-<wire x1="36.5" y1="8.9" x2="36.9" y2="8.5" width="0.2" layer="16"/>
-<wire x1="36.9" y1="8.5" x2="60" y2="8.5" width="0.2" layer="16"/>
-<wire x1="23.5" y1="14" x2="25" y2="12.5" width="0.2" layer="1"/>
-<wire x1="25" y1="12.5" x2="25" y2="10.5" width="0.2" layer="1"/>
-<wire x1="25" y1="10.5" x2="27" y2="8.5" width="0.2" layer="16"/>
+<via x="26.5" y="8" extent="1-16" drill="0.4"/>
 <wire x1="21" y1="25.87" x2="21" y2="27.5" width="0.2" layer="1"/>
 <wire x1="21" y1="27.5" x2="21" y2="28.7" width="0.2" layer="1"/>
 <wire x1="19.5" y1="23.87" x2="19.5" y2="23.88" width="0.2" layer="1"/>
@@ -4925,13 +4957,33 @@ design rules under a new name.</description>
 <wire x1="21" y1="25.38" x2="21" y2="25.87" width="0.2" layer="1"/>
 <wire x1="19.5" y1="23.87" x2="20.49" y2="24.86" width="0.2" layer="1"/>
 <wire x1="20.49" y1="24.86" x2="20.49" y2="24.87" width="0.2" layer="1"/>
+<wire x1="22" y1="15.5" x2="23.5" y2="14" width="0.2" layer="1"/>
+<wire x1="23.5" y1="14" x2="25.4" y2="14" width="0.2" layer="1"/>
+<wire x1="25.4" y1="14" x2="26" y2="14" width="0.2" layer="1"/>
+<wire x1="26" y1="14" x2="27.5" y2="12.5" width="0.2" layer="1"/>
+<wire x1="27.5" y1="12.5" x2="27.5" y2="11.5" width="0.2" layer="1"/>
+<wire x1="27.5" y1="11.5" x2="27.5" y2="10" width="0.2" layer="1"/>
+<wire x1="26.5" y1="8" x2="27.5" y2="9" width="0.2" layer="1"/>
+<wire x1="27.5" y1="9" x2="27.5" y2="10" width="0.2" layer="1"/>
+<wire x1="25.4" y1="13.97" x2="25.4" y2="14" width="0.2" layer="1"/>
+<wire x1="61.75" y1="15.8" x2="62.5" y2="15.05" width="0.2" layer="16"/>
+<wire x1="62.5" y1="15.05" x2="62.5" y2="9.5" width="0.2" layer="16"/>
+<wire x1="62.5" y1="9.5" x2="61.9" y2="8.9" width="0.2" layer="16"/>
+<wire x1="61.9" y1="8.9" x2="61.5" y2="8.5" width="0.2" layer="16"/>
+<wire x1="61.5" y1="8.5" x2="53.5" y2="8.5" width="0.2" layer="16"/>
+<wire x1="53.5" y1="8.5" x2="53" y2="8" width="0.2" layer="16"/>
+<wire x1="53" y1="8" x2="41.5" y2="8" width="0.2" layer="16"/>
+<wire x1="41.5" y1="8" x2="41" y2="8" width="0.2" layer="16"/>
+<wire x1="41" y1="8" x2="40.5" y2="8.5" width="0.2" layer="16"/>
+<wire x1="40.5" y1="8.5" x2="36.5" y2="8.5" width="0.2" layer="16"/>
+<wire x1="36.5" y1="8.5" x2="36" y2="8" width="0.2" layer="16"/>
+<wire x1="36" y1="8" x2="33.5" y2="8" width="0.2" layer="16"/>
+<wire x1="26.5" y1="8" x2="33.5" y2="8" width="0.2" layer="16"/>
 </signal>
 <signal name="N$49">
 <contactref element="LD2" pad="1"/>
 <contactref element="R51" pad="1"/>
-<wire x1="49" y1="24.27" x2="49" y2="25.5" width="0.2" layer="1"/>
-<wire x1="49" y1="25.5" x2="49.7" y2="26.2" width="0.2" layer="1"/>
-<wire x1="49.7" y1="26.2" x2="49.7" y2="27.5" width="0.2" layer="1"/>
+<wire x1="49" y1="24.27" x2="49.7" y2="27.5" width="0" layer="19" extent="1-1"/>
 </signal>
 <signal name="RF">
 <contactref element="CN9" pad="1"/>
@@ -4964,16 +5016,11 @@ design rules under a new name.</description>
 </polygon>
 <wire x1="19" y1="21.2" x2="19" y2="9.5" width="0.5" layer="1"/>
 <wire x1="19" y1="9.5" x2="19.5" y2="9" width="0.5" layer="1"/>
-<via x="36.3" y="8" extent="1-16" drill="0.4"/>
 <via x="36.3" y="6" extent="1-16" drill="0.4"/>
 <via x="36.3" y="4" extent="1-16" drill="0.4"/>
 <via x="36.3" y="2" extent="1-16" drill="0.4"/>
-<wire x1="55" y1="21.73" x2="56.5" y2="21.73" width="0.4" layer="1"/>
-<wire x1="56.5" y1="21.73" x2="56.5" y2="20.5" width="0.4" layer="1"/>
-<wire x1="56.5" y1="20.5" x2="59.5" y2="17.5" width="0.4" layer="1"/>
 <wire x1="59.5" y1="17.5" x2="59.5" y2="6" width="0.4" layer="1"/>
 <wire x1="57.7" y1="27.5" x2="56.5" y2="26.3" width="0.4" layer="1"/>
-<wire x1="56.5" y1="26.3" x2="56.5" y2="21.73" width="0.4" layer="1"/>
 <wire x1="19" y1="21.2" x2="18.8" y2="21.4" width="0.5" layer="1"/>
 <wire x1="18.8" y1="21.4" x2="18.8" y2="24.9" width="0.5" layer="1"/>
 <wire x1="18.8" y1="24.9" x2="19.4" y2="25.5" width="0.5" layer="1"/>
@@ -4995,6 +5042,8 @@ design rules under a new name.</description>
 <vertex x="64" y="9.5"/>
 <vertex x="64" y="1"/>
 </polygon>
+<wire x1="55" y1="21.73" x2="56.5" y2="26.3" width="0" layer="19" extent="1-1"/>
+<wire x1="59.5" y1="17.5" x2="55" y2="21.73" width="0" layer="19" extent="1-1"/>
 </signal>
 <signal name="N$59">
 <contactref element="U6" pad="1"/>
@@ -5039,24 +5088,12 @@ design rules under a new name.</description>
 <signal name="N$63">
 <contactref element="T1" pad="1"/>
 <contactref element="R52" pad="3"/>
-<wire x1="45.04" y1="16.25" x2="45" y2="16.29" width="0.2" layer="1"/>
-<wire x1="45" y1="16.29" x2="45" y2="18.5" width="0.2" layer="1"/>
-<via x="45" y="18.5" extent="1-16" drill="0.4"/>
-<wire x1="45" y1="18.5" x2="45.8" y2="19.3" width="0.2" layer="16"/>
-<wire x1="45.8" y1="19.3" x2="48.6" y2="19.3" width="0.2" layer="16"/>
-<wire x1="48.6" y1="19.3" x2="49.2" y2="19.3" width="0.2" layer="16"/>
-<wire x1="49.2" y1="19.3" x2="49.5" y2="19" width="0.2" layer="16"/>
-<wire x1="49.5" y1="19" x2="54.5" y2="19" width="0.2" layer="16"/>
-<wire x1="54.5" y1="19" x2="56" y2="20.5" width="0.2" layer="16"/>
-<wire x1="56" y1="20.5" x2="56.5" y2="21" width="0.2" layer="16"/>
-<wire x1="56.5" y1="21" x2="56.5" y2="26" width="0.2" layer="16"/>
-<wire x1="56.5" y1="26" x2="58" y2="27.5" width="0.2" layer="16"/>
-<wire x1="58" y1="27.5" x2="59.5" y2="27.5" width="0.2" layer="16"/>
 <wire x1="59.5" y1="27.5" x2="60.5" y2="28.5" width="0.2" layer="16"/>
 <wire x1="61.54" y1="54.46" x2="63.5" y2="52.5" width="0.2" layer="16"/>
-<wire x1="63.5" y1="52.5" x2="63.5" y2="35" width="0.2" layer="16"/>
-<wire x1="63.5" y1="35" x2="63.5" y2="31.5" width="0.2" layer="16"/>
+<wire x1="63.5" y1="52.5" x2="63.5" y2="39" width="0.2" layer="16"/>
+<wire x1="63.5" y1="39" x2="63.5" y2="31.5" width="0.2" layer="16"/>
 <wire x1="63.5" y1="31.5" x2="60.5" y2="28.5" width="0.2" layer="16"/>
+<wire x1="45.04" y1="18.25" x2="59.5" y2="27.5" width="0" layer="19" extent="1-16"/>
 </signal>
 <signal name="N$66">
 <via x="4.5" y="22" extent="1-16" drill="3.2" diameter="6.4516"/>
@@ -5091,29 +5128,12 @@ design rules under a new name.</description>
 <signal name="N$33">
 <contactref element="FB1" pad="1"/>
 <contactref element="T1" pad="6"/>
-<wire x1="45.04" y1="3.75" x2="45" y2="3.79" width="0.2" layer="1"/>
-<wire x1="45" y1="3.79" x2="45" y2="6.5" width="0.2" layer="1"/>
-<wire x1="45" y1="6.5" x2="46.5" y2="8" width="0.2" layer="1"/>
-<wire x1="46.5" y1="8" x2="46.5" y2="18" width="0.2" layer="1"/>
-<wire x1="46.5" y1="18" x2="46.5" y2="19" width="0.2" layer="1"/>
-<wire x1="46.5" y1="19" x2="45.5" y2="20" width="0.2" layer="1"/>
-<wire x1="45.5" y1="20" x2="45.5" y2="22.025" width="0.2" layer="1"/>
+<wire x1="45.04" y1="5.75" x2="45.5" y2="22.525" width="0" layer="19" extent="1-1"/>
 </signal>
 <signal name="N$64">
 <contactref element="FB1" pad="2"/>
 <contactref element="CN6" pad="2"/>
-<wire x1="57.4" y1="11.8" x2="57.4" y2="12.6" width="0.2" layer="16"/>
-<wire x1="57.4" y1="12.6" x2="55.7" y2="14.3" width="0.2" layer="16"/>
-<wire x1="45.5" y1="23.975" x2="45.525" y2="24" width="0.2" layer="1"/>
-<wire x1="45.525" y1="24" x2="46.5" y2="24" width="0.2" layer="1"/>
-<via x="48.5" y="18.5" extent="1-16" drill="0.4"/>
-<wire x1="55.7" y1="14.3" x2="55.7" y2="17.9" width="0.2" layer="16"/>
-<wire x1="55.7" y1="17.9" x2="55.1" y2="18.5" width="0.2" layer="16"/>
-<wire x1="48.5" y1="18.5" x2="55.1" y2="18.5" width="0.2" layer="16"/>
-<wire x1="47" y1="20.3" x2="47" y2="23.5" width="0.2" layer="1"/>
-<wire x1="47" y1="23.5" x2="46.5" y2="24" width="0.2" layer="1"/>
-<wire x1="48.5" y1="18.5" x2="47" y2="20" width="0.2" layer="1"/>
-<wire x1="47" y1="20" x2="47" y2="20.3" width="0.2" layer="1"/>
+<wire x1="57.4" y1="11.8" x2="45.5" y2="24.475" width="0" layer="19" extent="1-16"/>
 </signal>
 <signal name="N$72">
 <contactref element="FB2" pad="2"/>
@@ -5121,13 +5141,7 @@ design rules under a new name.</description>
 <wire x1="48.4" y1="11.8" x2="48.2" y2="12" width="0.2" layer="16"/>
 <wire x1="48.2" y1="12" x2="44" y2="12" width="0.2" layer="16"/>
 <via x="44" y="12" extent="1-16" drill="0.4"/>
-<wire x1="42.5" y1="19" x2="42.5" y2="20.525" width="0.2" layer="1"/>
-<wire x1="44" y1="12" x2="41.2" y2="14.8" width="0.2" layer="1"/>
-<wire x1="41.2" y1="14.8" x2="41.2" y2="15.5" width="0.2" layer="1"/>
-<wire x1="41.2" y1="15.5" x2="41.2" y2="17.45" width="0.2" layer="1"/>
-<wire x1="41.2" y1="17.45" x2="41.7" y2="17.95" width="0.2" layer="1"/>
-<wire x1="41.7" y1="17.95" x2="42.5" y2="18.75" width="0.2" layer="1"/>
-<wire x1="42.5" y1="18.75" x2="42.5" y2="19" width="0.2" layer="1"/>
+<wire x1="44" y1="12" x2="42.5" y2="22.525" width="0" layer="19" extent="1-16"/>
 </signal>
 <signal name="N$73">
 <contactref element="FB6" pad="2"/>
@@ -5135,19 +5149,14 @@ design rules under a new name.</description>
 <wire x1="39.4" y1="11.8" x2="39.4" y2="13.6" width="0.2" layer="16"/>
 <wire x1="39.4" y1="13.6" x2="38.5" y2="14.5" width="0.2" layer="16"/>
 <via x="38.5" y="14.5" extent="1-16" drill="0.4"/>
-<wire x1="39" y1="20.525" x2="39" y2="18.5" width="0.2" layer="1"/>
-<wire x1="39" y1="18.5" x2="38.5" y2="18" width="0.2" layer="1"/>
-<wire x1="38.5" y1="18" x2="38.5" y2="14.5" width="0.2" layer="1"/>
+<wire x1="38.5" y1="14.5" x2="38.5" y2="22.025" width="0" layer="19" extent="1-1"/>
 </signal>
 <signal name="N$74">
 <contactref element="FB6" pad="1"/>
 <contactref element="LD2" pad="4"/>
-<wire x1="39" y1="22.475" x2="39" y2="24.5" width="0.2" layer="1"/>
-<via x="39" y="24.5" extent="1-16" drill="0.4"/>
-<wire x1="55" y1="24.27" x2="53.73" y2="24.27" width="0.2" layer="1"/>
-<wire x1="53.73" y1="24.27" x2="53.5" y2="24.5" width="0.2" layer="1"/>
-<via x="53.5" y="24.5" extent="1-16" drill="0.4"/>
-<wire x1="39" y1="24.5" x2="53.5" y2="24.5" width="0.2" layer="16"/>
+<via x="38.5" y="25.5" extent="1-16" drill="0.4"/>
+<wire x1="38.5" y1="23.975" x2="55" y2="24.27" width="0" layer="19" extent="1-1"/>
+<wire x1="38.5" y1="25.5" x2="38.5" y2="23.975" width="0" layer="19" extent="1-1"/>
 </signal>
 <signal name="N$44">
 <contactref element="FB3" pad="1"/>
@@ -5163,8 +5172,6 @@ design rules under a new name.</description>
 <signal name="N$75">
 <contactref element="FB3" pad="2"/>
 <contactref element="CN8" pad="2"/>
-<wire x1="30.4" y1="11.8" x2="34.8" y2="11.8" width="0.2" layer="16"/>
-<wire x1="34.8" y1="11.8" x2="35.5" y2="12.5" width="0.2" layer="16"/>
 <via x="35.5" y="12.5" extent="1-16" drill="0.4"/>
 <wire x1="36.5" y1="26.2" x2="36.5" y2="28.5" width="0.2" layer="1"/>
 <wire x1="36.5" y1="28.5" x2="35.975" y2="29.025" width="0.2" layer="1"/>
@@ -5175,37 +5182,32 @@ design rules under a new name.</description>
 <wire x1="36.8" y1="20" x2="36.8" y2="19.3" width="0.2" layer="1"/>
 <wire x1="36.8" y1="19.3" x2="35.5" y2="18" width="0.2" layer="1"/>
 <wire x1="35.5" y1="18" x2="35.5" y2="12.5" width="0.2" layer="1"/>
+<wire x1="30.4" y1="11.8" x2="32.3" y2="11.8" width="0.2" layer="16"/>
+<wire x1="32.3" y1="11.8" x2="33" y2="12.5" width="0.2" layer="16"/>
+<wire x1="33" y1="12.5" x2="35.5" y2="12.5" width="0.2" layer="16"/>
 </signal>
 <signal name="N$76">
 <contactref element="CN5" pad="2"/>
 <contactref element="FB4" pad="1"/>
-<via x="24" y="12" extent="1-16" drill="0.4"/>
+<via x="23.5" y="12" extent="1-16" drill="0.4"/>
 <wire x1="21.4" y1="11.8" x2="21.6" y2="12" width="0.4" layer="16"/>
-<wire x1="21.6" y1="12" x2="24" y2="12" width="0.4" layer="16"/>
-<wire x1="24" y1="12" x2="25.65" y2="12" width="0.2" layer="16"/>
-<wire x1="25.65" y1="12" x2="27.2" y2="10.45" width="0.2" layer="16"/>
+<wire x1="21.6" y1="12" x2="23.5" y2="12" width="0.4" layer="16"/>
 <wire x1="27.2" y1="10.45" x2="28.15" y2="9.5" width="0.2" layer="16"/>
-<wire x1="28.15" y1="9.5" x2="29" y2="9.5" width="0.2" layer="16"/>
-<wire x1="29" y1="9.5" x2="35" y2="9.5" width="0.2" layer="16"/>
-<wire x1="35" y1="9.5" x2="35.5" y2="10" width="0.2" layer="16"/>
-<wire x1="35.5" y1="10" x2="36" y2="10" width="0.2" layer="16"/>
-<wire x1="36" y1="10" x2="36.8" y2="10" width="0.2" layer="16"/>
-<wire x1="36.8" y1="10" x2="37.3" y2="9.5" width="0.2" layer="16"/>
-<wire x1="37.3" y1="9.5" x2="39.5" y2="9.5" width="0.2" layer="16"/>
-<wire x1="39.5" y1="9.5" x2="43.5" y2="9.5" width="0.2" layer="16"/>
 <wire x1="40.5" y1="30.5" x2="40.5" y2="26.5" width="0.2" layer="1"/>
-<wire x1="40.5" y1="26.5" x2="41" y2="26" width="0.2" layer="1"/>
-<wire x1="41" y1="26" x2="41.5" y2="25.5" width="0.2" layer="1"/>
-<wire x1="41.5" y1="25.5" x2="43.5" y2="23.5" width="0.2" layer="1"/>
-<wire x1="43.5" y1="23.5" x2="43.65" y2="23.35" width="0.2" layer="1"/>
-<wire x1="43.65" y1="23.35" x2="43.65" y2="20.45" width="0.2" layer="1"/>
-<wire x1="43.65" y1="20.45" x2="43.65" y2="13.6" width="0.2" layer="1"/>
-<wire x1="43.65" y1="13.6" x2="44.75" y2="12.5" width="0.2" layer="1"/>
-<wire x1="44.75" y1="12.5" x2="44.75" y2="10.75" width="0.2" layer="1"/>
-<wire x1="44.75" y1="10.75" x2="44" y2="10" width="0.2" layer="1"/>
-<wire x1="43.5" y1="9.5" x2="44" y2="10" width="0.2" layer="16"/>
-<via x="44" y="10" extent="1-16" drill="0.4"/>
+<via x="45" y="10" extent="1-16" drill="0.4"/>
 <wire x1="40.5" y1="30.5" x2="40.5" y2="34.525" width="0.2" layer="1"/>
+<wire x1="27.2" y1="10.45" x2="27.2" y2="11.3" width="0.2" layer="16"/>
+<wire x1="27.2" y1="11.3" x2="26.5" y2="12" width="0.2" layer="16"/>
+<wire x1="26.5" y1="12" x2="23.5" y2="12" width="0.2" layer="16"/>
+<wire x1="42" y1="9" x2="44" y2="9" width="0.2" layer="16"/>
+<wire x1="44" y1="9" x2="45" y2="10" width="0.2" layer="16"/>
+<wire x1="28.15" y1="9.5" x2="28.65" y2="9" width="0.2" layer="16"/>
+<wire x1="28.65" y1="9" x2="35" y2="9" width="0.2" layer="16"/>
+<wire x1="35" y1="9" x2="35.5" y2="9.5" width="0.2" layer="16"/>
+<wire x1="35.5" y1="9.5" x2="38.5" y2="9.5" width="0.2" layer="16"/>
+<wire x1="38.5" y1="9.5" x2="41.5" y2="9.5" width="0.2" layer="16"/>
+<wire x1="41.5" y1="9.5" x2="42" y2="9" width="0.2" layer="16"/>
+<wire x1="41.5" y1="9.5" x2="40.5" y2="26.5" width="0" layer="19" extent="1-16"/>
 </signal>
 <signal name="N$77">
 <contactref element="CN3" pad="2"/>
@@ -5257,15 +5259,7 @@ design rules under a new name.</description>
 <signal name="N$78">
 <contactref element="R48" pad="2"/>
 <contactref element="T2" pad="6"/>
-<wire x1="57.04" y1="3.75" x2="58.5" y2="5.21" width="0.25" layer="1"/>
-<wire x1="58.5" y1="5.21" x2="58.5" y2="17.5" width="0.25" layer="1"/>
-<wire x1="58.5" y1="17.5" x2="56" y2="20" width="0.25" layer="1"/>
-<wire x1="56" y1="20" x2="54.5" y2="20" width="0.25" layer="1"/>
-<wire x1="54.5" y1="20" x2="53.7" y2="20.8" width="0.25" layer="1"/>
-<wire x1="53.7" y1="20.8" x2="52.5" y2="22" width="0.2" layer="1"/>
-<wire x1="52.5" y1="22" x2="52.5" y2="25" width="0.2" layer="1"/>
-<wire x1="52.5" y1="25" x2="53.7" y2="26.2" width="0.2" layer="1"/>
-<wire x1="53.7" y1="26.2" x2="53.7" y2="27.5" width="0.2" layer="1"/>
+<wire x1="57.04" y1="5.75" x2="53.7" y2="27.5" width="0" layer="19" extent="1-1"/>
 </signal>
 <signal name="N$81">
 <contactref element="R49" pad="2"/>
@@ -5286,20 +5280,12 @@ design rules under a new name.</description>
 <signal name="N$65">
 <contactref element="C38" pad="2"/>
 <contactref element="T2" pad="1"/>
-<wire x1="57.04" y1="16.25" x2="57" y2="16.29" width="0.2" layer="1"/>
 <wire x1="62.25" y1="70" x2="62.25" y2="68.75" width="0.4" layer="1"/>
 <wire x1="62.25" y1="68.75" x2="62.5" y2="68.5" width="0.4" layer="1"/>
 <wire x1="62.5" y1="68.5" x2="63.5" y2="68.5" width="0.4" layer="1"/>
 <wire x1="63.5" y1="68.5" x2="64" y2="68" width="0.4" layer="1"/>
 <wire x1="64" y1="68" x2="64" y2="64.5" width="0.4" layer="1"/>
 <wire x1="64" y1="64.5" x2="63" y2="63.5" width="0.4" layer="1"/>
-<wire x1="57" y1="16.29" x2="57" y2="18" width="0.4" layer="1"/>
-<wire x1="57" y1="18" x2="56.5" y2="18.5" width="0.4" layer="1"/>
-<wire x1="56.5" y1="18.5" x2="55.7" y2="19.3" width="0.4" layer="1"/>
-<wire x1="55.7" y1="19.3" x2="54" y2="19.3" width="0.4" layer="1"/>
-<wire x1="54" y1="19.3" x2="51.85" y2="21.45" width="0.4" layer="1"/>
-<wire x1="51.85" y1="21.45" x2="51.85" y2="25.45" width="0.4" layer="1"/>
-<wire x1="51.85" y1="25.45" x2="52.5" y2="26.1" width="0.4" layer="1"/>
 <wire x1="52.5" y1="26.1" x2="52.5" y2="28" width="0.4" layer="1"/>
 <wire x1="52.5" y1="28" x2="53.5" y2="29" width="0.4" layer="1"/>
 <wire x1="53.5" y1="29" x2="53.5" y2="40.5" width="0.4" layer="1"/>
@@ -5313,6 +5299,7 @@ design rules under a new name.</description>
 <wire x1="62.8" y1="53.7" x2="62.8" y2="40.8" width="0.4" layer="1"/>
 <wire x1="62.8" y1="40.8" x2="62.5" y2="40.5" width="0.4" layer="1"/>
 <wire x1="53.5" y1="40.5" x2="62.5" y2="40.5" width="0.4" layer="16"/>
+<wire x1="57.04" y1="18.25" x2="52.5" y2="26.1" width="0" layer="19" extent="1-1"/>
 </signal>
 <signal name="N$61">
 <contactref element="R47" pad="2"/>
@@ -5328,11 +5315,7 @@ design rules under a new name.</description>
 <signal name="N$79">
 <contactref element="C47" pad="2"/>
 <contactref element="FB2" pad="1"/>
-<wire x1="42.5" y1="22.475" x2="42.5" y2="23.5" width="0.2" layer="1"/>
-<wire x1="42.5" y1="23.5" x2="40.5" y2="25.5" width="0.2" layer="1"/>
-<wire x1="40.5" y1="25.5" x2="39" y2="25.5" width="0.2" layer="1"/>
-<wire x1="39" y1="25.5" x2="38.7" y2="25.8" width="0.2" layer="1"/>
-<wire x1="38.7" y1="25.8" x2="38.7" y2="27" width="0.2" layer="1"/>
+<wire x1="42.5" y1="24.475" x2="38.7" y2="27" width="0" layer="19" extent="1-1"/>
 </signal>
 <signal name="N$62">
 <contactref element="CN8" pad="10"/>
@@ -5406,8 +5389,6 @@ design rules under a new name.</description>
 <signal name="N$85">
 <contactref element="CN10" pad="2"/>
 <contactref element="R37" pad="1"/>
-<wire x1="12.4" y1="11.8" x2="17.8" y2="11.8" width="0.2" layer="16"/>
-<wire x1="17.8" y1="11.8" x2="20" y2="14" width="0.2" layer="16"/>
 <wire x1="20" y1="14" x2="24" y2="14" width="0.2" layer="16"/>
 <wire x1="24" y1="14" x2="24.5" y2="13.5" width="0.2" layer="16"/>
 <wire x1="24.5" y1="13.5" x2="27" y2="13.5" width="0.2" layer="16"/>
@@ -5417,9 +5398,6 @@ design rules under a new name.</description>
 <wire x1="33" y1="13.5" x2="36" y2="13.5" width="0.2" layer="16"/>
 <wire x1="36" y1="13.5" x2="37" y2="14.5" width="0.2" layer="16"/>
 <wire x1="37" y1="14.5" x2="37" y2="16" width="0.2" layer="16"/>
-<wire x1="37" y1="16" x2="40.5" y2="19.5" width="0.2" layer="16"/>
-<wire x1="40.5" y1="19.5" x2="43.5" y2="19.5" width="0.2" layer="16"/>
-<wire x1="43.5" y1="19.5" x2="45" y2="21" width="0.2" layer="16"/>
 <via x="54.5" y="28.7" extent="1-16" drill="0.4"/>
 <wire x1="54.5" y1="28.7" x2="54.15" y2="29.05" width="0.2" layer="1"/>
 <wire x1="54.15" y1="29.05" x2="54.15" y2="37.55" width="0.2" layer="1"/>
@@ -5433,9 +5411,6 @@ design rules under a new name.</description>
 <wire x1="55" y1="52" x2="55" y2="49" width="0.2" layer="16"/>
 <wire x1="55" y1="49" x2="54" y2="48" width="0.2" layer="16"/>
 <wire x1="54" y1="48" x2="54" y2="42.5" width="0.2" layer="16"/>
-<wire x1="54.5" y1="23" x2="54.5" y2="28.7" width="0.2" layer="16"/>
-<wire x1="45" y1="21" x2="52.5" y2="21" width="0.2" layer="16"/>
-<wire x1="52.5" y1="21" x2="54.5" y2="23" width="0.2" layer="16"/>
 <wire x1="50" y1="58.5" x2="52.5" y2="58.5" width="0.2" layer="16"/>
 <wire x1="52.5" y1="58.5" x2="53.5" y2="57.5" width="0.2" layer="16"/>
 <wire x1="53.5" y1="57.5" x2="53.5" y2="53.5" width="0.2" layer="16"/>
@@ -5447,6 +5422,14 @@ design rules under a new name.</description>
 <wire x1="46.2" y1="60.8" x2="47" y2="60" width="0.2" layer="1"/>
 <wire x1="47" y1="60" x2="47" y2="59.5" width="0.2" layer="1"/>
 <wire x1="47" y1="59.5" x2="48" y2="58.5" width="0.2" layer="1"/>
+<wire x1="12.4" y1="11.8" x2="12.6" y2="12" width="0.2" layer="16"/>
+<wire x1="12.6" y1="12" x2="14.5" y2="12" width="0.2" layer="16"/>
+<wire x1="14.5" y1="12" x2="16" y2="13.5" width="0.2" layer="16"/>
+<wire x1="16" y1="13.5" x2="16.5" y2="13.5" width="0.2" layer="16"/>
+<wire x1="16.5" y1="13.5" x2="18" y2="13.5" width="0.2" layer="16"/>
+<wire x1="18" y1="13.5" x2="18.5" y2="14" width="0.2" layer="16"/>
+<wire x1="18.5" y1="14" x2="20" y2="14" width="0.2" layer="16"/>
+<wire x1="37" y1="16" x2="54.15" y2="29.05" width="0" layer="19" extent="1-16"/>
 </signal>
 <signal name="+VEXT">
 <contactref element="SW3" pad="2"/>
@@ -5474,18 +5457,16 @@ design rules under a new name.</description>
 <wire x1="5.5" y1="64.5" x2="4.75" y2="65.25" width="1.27" layer="16"/>
 <wire x1="4.75" y1="65.25" x2="4.75" y2="68.5" width="1.27" layer="16"/>
 <wire x1="5.5" y1="59.27" x2="3" y2="56.77" width="1.27" layer="16"/>
-<contactref element="J7" pad="2"/>
-<wire x1="3" y1="56.77" x2="3" y2="54.77" width="1.27" layer="16"/>
+<contactref element="R21" pad="1"/>
+<wire x1="3" y1="56.77" x2="-6" y2="51.95" width="0" layer="19" extent="1-16"/>
 </signal>
 <signal name="APTT">
 <contactref element="CN9" pad="10"/>
 <contactref element="CN12" pad="14"/>
 <contactref element="C45" pad="1"/>
-<wire x1="43.75" y1="15.8" x2="43.75" y2="12.75" width="0.2" layer="16"/>
-<wire x1="43.75" y1="12.75" x2="43" y2="12" width="0.2" layer="16"/>
-<wire x1="43" y1="12" x2="43" y2="10.5" width="0.2" layer="16"/>
-<wire x1="43" y1="10.5" x2="42.5" y2="10" width="0.2" layer="16"/>
-<wire x1="42.5" y1="10" x2="37.5" y2="10" width="0.2" layer="16"/>
+<wire x1="41.5" y1="11.5" x2="41.5" y2="10.5" width="0.2" layer="16"/>
+<wire x1="41.5" y1="10.5" x2="41" y2="10" width="0.2" layer="16"/>
+<wire x1="41" y1="10" x2="37.5" y2="10" width="0.2" layer="16"/>
 <wire x1="37.5" y1="10" x2="37" y2="10.5" width="0.2" layer="16"/>
 <wire x1="37" y1="10.5" x2="36.5" y2="11" width="0.2" layer="16"/>
 <via x="36.5" y="11" extent="1-16" drill="0.4"/>
@@ -5505,6 +5486,8 @@ design rules under a new name.</description>
 <wire x1="37" y1="21.8" x2="37.3" y2="21.5" width="0.2" layer="1"/>
 <wire x1="37.3" y1="21.5" x2="37.3" y2="18.8" width="0.2" layer="1"/>
 <wire x1="37.3" y1="18.8" x2="36.5" y2="18" width="0.2" layer="1"/>
+<wire x1="41.5" y1="11.5" x2="43.75" y2="13.75" width="0.2" layer="16"/>
+<wire x1="43.75" y1="13.75" x2="43.75" y2="15.8" width="0.2" layer="16"/>
 </signal>
 <signal name="N$6">
 <contactref element="R20" pad="2"/>
@@ -5838,12 +5821,17 @@ design rules under a new name.</description>
 <approved hash="19,1,af4e38883f75a8b3"/>
 <approved hash="19,1,ade23a243fe9a82f"/>
 <approved hash="19,1,a8ba3f7c3fd1a817"/>
+<approved hash="19,1,c1ff063903fec438"/>
 <approved hash="19,1,c4a7036103c6c400"/>
 <approved hash="19,1,c35304950362c4a4"/>
-<approved hash="19,1,c1ff063903fec438"/>
-<approved hash="19,1,2de63a203fe02826"/>
 <approved hash="19,1,28be3f783fd8281e"/>
 <approved hash="19,1,2f4a388c3f7c28ba"/>
+<approved hash="19,1,2de63a203fe02826"/>
+<approved hash="4,1,9ae54312fc8ca549"/>
+<approved hash="4,1,87b3ae3e0f9499c4"/>
+<approved hash="4,1,188e489147353a85"/>
+<approved hash="4,1,5ed21f9f6a8db497"/>
+<approved hash="4,1,ed2faf7e19d4f70c"/>
 <approved hash="4,16,9dc4933833e8c785"/>
 </errors>
 </board>

diff --git a/smartmic/SM1000-REV-B2/SM1000-REV-B2.pro b/smartmic/SM1000-REV-B2/SM1000-REV-B2.pro
new file mode 100644 (file)
index 0000000..747106a
--- /dev/null
+++ b/smartmic/SM1000-REV-B2/SM1000-REV-B2.pro
@@ -0,0 +1,25 @@
+EAGLE AutoRouter Statistics:\r
+\r
+Job           : C:/Users/rbarnich/smartmic/SM1000-REV-B2/SM1000-REV-B2.brd\r
+\r
+Start at      : 10:13:59 (7/15/2014)\r
+End at        : 10:13:59 (7/15/2014)\r
+Elapsed time  : 00:00:00\r
+\r
+Signals       :   122   RoutingGrid: 50 mil  Layers: 3\r
+Connections   :   342   predefined:  339 ( 198 Vias )\r
+\r
+Router memory :   110880\r
+\r
+Passname          :    Busses     Route Optimize1 Optimize2 Optimize3 Optimize4\r
+\r
+Time per pass     :  00:00:00  00:00:00  00:00:00  00:00:00  00:00:00  00:00:00\r
+Number of Ripups  :         0         0         0         0         0         0\r
+max. Level        :         0         0         0         0         0         0\r
+max. Total        :         0         0         0         0         0         0\r
+\r
+Routed            :         0         3         3         3         3         3\r
+Vias              :         0        12         3         3         3         3\r
+Resolution        :    99.1 %   100.0 %   100.0 %   100.0 %   100.0 %   100.0 %\r
+\r
+Final             : 99.1% finished. Polygons may have fallen apart.\r

diff --git a/smartmic/SM1000-REV-B2/SM1000-REV-B2.sch b/smartmic/SM1000-REV-B2/SM1000-REV-B2.sch
index c8135d14f0320980f96baf68deee619ee503dff2..8f901a0a544c7dfa2c1f0f13bb98ef3c274a1532 100644 (file)
--- a/smartmic/SM1000-REV-B2/SM1000-REV-B2.sch
+++ b/smartmic/SM1000-REV-B2/SM1000-REV-B2.sch
@@ -273,6 +273,8 @@
 <wire x1="-9.9" y1="-3" x2="-9.9" y2="1.2" width="0" layer="39"/>
 <wire x1="-9.9" y1="1.2" x2="-5.9" y2="1.2" width="0" layer="39"/>
 <wire x1="-5.9" y1="1.2" x2="-5.9" y2="5.7" width="0" layer="39"/>
+<hole x="-2.5" y="0" drill="1.7"/>
+<hole x="4.5" y="0" drill="1.7"/>
 </package>
 <package name="SRN6045">
 <smd name="1" x="-2.15" y="0" dx="6" dy="2" layer="1" rot="R90"/>
@@ -455,12 +457,12 @@ INFINEON, www.infineon.com/cmc_upload/0/000/010/257/eh_db_5b.pdf</description>
 <text x="-5.5" y="6.5" size="1" layer="25" ratio="10">&gt;NAME</text>
 </package>
 <package name="SW-PWR">
-<pad name="1" x="2.5" y="-1.25" drill="0.5" shape="square"/>
-<pad name="2" x="0" y="-1.25" drill="0.5"/>
-<pad name="3" x="-2.5" y="-1.25" drill="0.5"/>
-<pad name="4" x="2.5" y="1.25" drill="0.5"/>
-<pad name="5" x="0" y="1.25" drill="0.5"/>
-<pad name="6" x="-2.5" y="1.25" drill="0.5"/>
+<pad name="1" x="2.5" y="-1.25" drill="1" diameter="1.778" shape="square"/>
+<pad name="2" x="0" y="-1.25" drill="1" diameter="1.778"/>
+<pad name="3" x="-2.5" y="-1.25" drill="1" diameter="1.778"/>
+<pad name="4" x="2.5" y="1.25" drill="1" diameter="1.778"/>
+<pad name="5" x="0" y="1.25" drill="1" diameter="1.778"/>
+<pad name="6" x="-2.5" y="1.25" drill="1" diameter="1.778"/>
 <wire x1="-4" y1="3" x2="5" y2="3" width="0.15" layer="21"/>
 <wire x1="-4.5" y1="-3" x2="5" y2="-3" width="0.15" layer="21"/>
 <wire x1="8.7" y1="3" x2="8.7" y2="-3" width="0.15" layer="21"/>
@@ -717,6 +719,22 @@ Source: http://cache.national.com/ds/LM/LM386.pdf</description>
 <text x="-2.5" y="6" size="1" layer="25" ratio="10">&gt;NAME</text>
 <circle x="0" y="0" radius="5.59016875" width="0.01" layer="39"/>
 </package>
+<package name="RR0805">
+<description>&lt;b&gt;RESISTOR&lt;/b&gt;&lt;p&gt;
+chip</description>
+<wire x1="-0.41" y1="0.635" x2="0.41" y2="0.635" width="0.1524" layer="51"/>
+<wire x1="-0.41" y1="-0.635" x2="0.41" y2="-0.635" width="0.1524" layer="51"/>
+<wire x1="-1.425" y1="0.95" x2="1.425" y2="0.95" width="0.0508" layer="39"/>
+<wire x1="1.425" y1="0.95" x2="1.425" y2="-0.95" width="0.0508" layer="39"/>
+<wire x1="1.425" y1="-0.95" x2="-1.425" y2="-0.95" width="0.0508" layer="39"/>
+<wire x1="-1.425" y1="-0.95" x2="-1.425" y2="0.95" width="0.0508" layer="39"/>
+<smd name="1" x="-0.95" y="0" dx="0.7" dy="1.3" layer="1" roundness="25"/>
+<smd name="2" x="0.95" y="0" dx="0.7" dy="1.3" layer="1" roundness="25"/>
+<text x="-1.462" y="1.116" size="1" layer="25" ratio="10">&gt;NAME</text>
+<rectangle x1="0.4064" y1="-0.6985" x2="1.0564" y2="0.7015" layer="51"/>
+<rectangle x1="-1.0668" y1="-0.6985" x2="-0.4168" y2="0.7015" layer="51"/>
+<rectangle x1="-0.1999" y1="-0.5001" x2="0.1999" y2="0.5001" layer="35"/>
+</package>
 </packages>
 <symbols>
 <symbol name="MJ-3523-SMT">
@@ -1184,6 +1202,21 @@ Source: http://cache.national.com/ds/LM/LM386.pdf</description>
 <text x="-17.78" y="20.32" size="1.4224" layer="95" ratio="10">&gt;NAME</text>
 <text x="0" y="20.32" size="1.4224" layer="95" ratio="10">&gt;VALUE</text>
 </symbol>
+<symbol name="R">
+<wire x1="-2.54" y1="0" x2="-2.159" y2="1.016" width="0.2032" layer="94"/>
+<wire x1="-2.159" y1="1.016" x2="-1.524" y2="-1.016" width="0.2032" layer="94"/>
+<wire x1="-1.524" y1="-1.016" x2="-0.889" y2="1.016" width="0.2032" layer="94"/>
+<wire x1="-0.889" y1="1.016" x2="-0.254" y2="-1.016" width="0.2032" layer="94"/>
+<wire x1="-0.254" y1="-1.016" x2="0.381" y2="1.016" width="0.2032" layer="94"/>
+<wire x1="0.381" y1="1.016" x2="1.016" y2="-1.016" width="0.2032" layer="94"/>
+<wire x1="1.016" y1="-1.016" x2="1.651" y2="1.016" width="0.2032" layer="94"/>
+<wire x1="1.651" y1="1.016" x2="2.286" y2="-1.016" width="0.2032" layer="94"/>
+<wire x1="2.286" y1="-1.016" x2="2.54" y2="0" width="0.2032" layer="94"/>
+<text x="-2.54" y="5.08" size="1.4224" layer="95" ratio="9">&gt;NAME</text>
+<text x="-2.54" y="2.54" size="1.4224" layer="96" ratio="9">&gt;VALUE</text>
+<pin name="2" x="5.08" y="0" visible="off" length="short" direction="pas" swaplevel="1" rot="R180"/>
+<pin name="1" x="-5.08" y="0" visible="off" length="short" direction="pas" swaplevel="1"/>
+</symbol>
 </symbols>
 <devicesets>
 <deviceset name="MJ-3523-SMT" prefix="CN">
@@ -1590,6 +1623,22 @@ Source: http://cache.national.com/ds/LM/LM386.pdf</description>
 </device>
 </devices>
 </deviceset>
+<deviceset name="RES0805" prefix="R">
+<gates>
+<gate name="G$1" symbol="R" x="0" y="0"/>
+</gates>
+<devices>
+<device name="" package="RR0805">
+<connects>
+<connect gate="G$1" pin="1" pad="1"/>
+<connect gate="G$1" pin="2" pad="2"/>
+</connects>
+<technologies>
+<technology name=""/>
+</technologies>
+</device>
+</devices>
+</deviceset>
 </devicesets>
 </library>
 <library name="_Coherix">
@@ -3867,11 +3916,9 @@ http://www.weartronics.com/</description>
 <part name="V34" library="A-SUPPLY2" deviceset="GND" device=""/>
 <part name="LED5" library="_Coherix" deviceset="LTST-C" device="" value="LED-RED,V"/>
 <part name="R17" library="AA-ipc-7351-resistor" deviceset="RESISTOR_" device="0603" value="1K,1%"/>
-<part name="J2" library="_Coherix" deviceset="JMP-2PIN" device=""/>
 <part name="V35" library="A-SUPPLY2" deviceset="GND" device=""/>
 <part name="U$2" library="A-SUPPLY2" deviceset="+3.3V" device=""/>
 <part name="V36" library="A-SUPPLY2" deviceset="VDD" device=""/>
-<part name="SH2" library="_Coherix" deviceset="SHUNT,0.1IN" device=""/>
 <part name="LED1" library="_RoweTel" deviceset="LTST-S220K" device="" value="LED-RED,RA"/>
 <part name="LED2" library="_RoweTel" deviceset="LTST-S220K" device="" value="LED-RED,RA"/>
 <part name="LED3" library="_RoweTel" deviceset="LTST-S220K" device="" value="LED-GRN,RA"/>
@@ -4048,8 +4095,6 @@ http://www.weartronics.com/</description>
 <part name="U$1" library="A-SUPPLY2" deviceset="+VIN" device=""/>
 <part name="U$7" library="A-SUPPLY2" deviceset="+VEXT" device=""/>
 <part name="V71" library="A-SUPPLY2" deviceset="GND" device=""/>
-<part name="J7" library="_Coherix" deviceset="JMP-2PIN" device=""/>
-<part name="SH6" library="_Coherix" deviceset="SHUNT,0.1IN" device=""/>
 <part name="C52" library="AA-ipc-7351-capacitor" deviceset="CAPACITOR_" device="0603" value="100nF,16V"/>
 <part name="C53" library="AA-ipc-7351-capacitor" deviceset="CAPACITOR_" device="0603" value="10nF,16V"/>
 <part name="V112" library="A-SUPPLY2" deviceset="GND" device=""/>
@@ -4116,6 +4161,8 @@ http://www.weartronics.com/</description>
 <part name="V122" library="A-SUPPLY2" deviceset="GND" device=""/>
 <part name="R9" library="SM1000" deviceset="RCL1218" device="" value="10,5%,1218"/>
 <part name="R11" library="AA-ipc-7351-resistor" deviceset="RESISTOR_" device="0603" value="100,1%"/>
+<part name="R18" library="_RoweTel" deviceset="RES0805" device="" value="0 Ohm"/>
+<part name="R21" library="_RoweTel" deviceset="RES0805" device="" value="0 Ohm"/>
 </parts>
 <sheets>
 <sheet>
@@ -4333,11 +4380,9 @@ http://www.weartronics.com/</description>
 <attribute name="NAME" x="289.56" y="149.86" size="1.4224" layer="95" ratio="9"/>
 <attribute name="VALUE" x="289.56" y="147.32" size="1.4224" layer="96" ratio="9"/>
 </instance>
-<instance part="J2" gate="G$1" x="294.64" y="154.94"/>
 <instance part="V35" gate="GND" x="287.02" y="127"/>
 <instance part="U$2" gate="G$1" x="287.02" y="157.48"/>
 <instance part="V36" gate="G$1" x="304.8" y="154.94" rot="R270"/>
-<instance part="SH2" gate="G$1" x="294.64" y="165.1"/>
 <instance part="LED1" gate="G$1" x="35.56" y="220.98" smashed="yes" rot="R90">
 <attribute name="NAME" x="45.72" y="218.44" size="1.4224" layer="95" ratio="9"/>
 <attribute name="VALUE" x="45.72" y="215.9" size="1.4224" layer="96" ratio="9"/>
@@ -4552,6 +4597,7 @@ http://www.weartronics.com/</description>
 </instance>
 <instance part="V123" gate="G$1" x="109.22" y="266.7"/>
 <instance part="U$3" gate="G$1" x="114.3" y="266.7"/>
+<instance part="R18" gate="G$1" x="297.18" y="154.94"/>
 </instances>
 <busses>
 </busses>
@@ -4658,9 +4704,9 @@ http://www.weartronics.com/</description>
 <junction x="99.06" y="30.48"/>
 </segment>
 <segment>
-<pinref part="J2" gate="G$1" pin="2"/>
-<wire x1="299.72" y1="154.94" x2="304.8" y2="154.94" width="0.1524" layer="91"/>
+<wire x1="302.26" y1="154.94" x2="304.8" y2="154.94" width="0.1524" layer="91"/>
 <pinref part="V36" gate="G$1" pin="VDD"/>
+<pinref part="R18" gate="G$1" pin="2"/>
 </segment>
 <segment>
 <pinref part="R4" gate="G$1" pin="1"/>
@@ -5178,7 +5224,6 @@ http://www.weartronics.com/</description>
 <segment>
 <pinref part="U$2" gate="G$1" pin="+3.3V"/>
 <wire x1="287.02" y1="154.94" x2="287.02" y2="157.48" width="0.1524" layer="91"/>
-<pinref part="J2" gate="G$1" pin="1"/>
 <wire x1="287.02" y1="154.94" x2="292.1" y2="154.94" width="0.1524" layer="91"/>
 <junction x="287.02" y="154.94"/>
 <pinref part="U2" gate="G$1" pin="VOUT"/>
@@ -5192,6 +5237,7 @@ http://www.weartronics.com/</description>
 <wire x1="279.4" y1="154.94" x2="287.02" y2="154.94" width="0.1524" layer="91"/>
 <pinref part="R17" gate="G$1" pin="2"/>
 <wire x1="287.02" y1="152.4" x2="287.02" y2="154.94" width="0.1524" layer="91"/>
+<pinref part="R18" gate="G$1" pin="1"/>
 </segment>
 </net>
 <net name="+5V" class="0">
@@ -5743,79 +5789,13 @@ http://www.weartronics.com/</description>
 <text x="419.1" y="269.24" size="1.4224" layer="94" ratio="10">B</text>
 <text x="424.18" y="269.24" size="1.4224" layer="94" ratio="10">RGB</text>
 <text x="264.16" y="266.7" size="2.54" layer="94" ratio="10">EXT. PTT INPUT</text>
-<text x="332.74" y="50.8" size="1.27" layer="94" ratio="10">1. Change U5 TPS54329E to RT8250</text>
-<text x="332.74" y="53.34" size="1.27" layer="94" ratio="10">2. Move LED8 to 5V </text>
-<text x="332.74" y="55.88" size="1.27" layer="94" ratio="10">3. Change rig mic amp circuit to pot on transformer output.</text>
-<text x="332.74" y="58.42" size="1.27" layer="94" ratio="10">4. Change mic preamp circuit to op-amp per DR.</text>
-<text x="332.74" y="60.96" size="1.27" layer="94" ratio="10">5. Add ext. PTT connector and cpu DI.</text>
-<text x="332.74" y="63.5" size="1.27" layer="94" ratio="10">6. Bring GND, RF(GND) &amp; +VEXT to IC1 connector.</text>
-<text x="332.74" y="66.04" size="1.27" layer="94" ratio="10">7. Change PCB from 4 layer to 2 layer.</text>
-<text x="332.74" y="68.58" size="1.27" layer="94" ratio="10">8. Change processor from STM32F407 to STM32F405.</text>
-<text x="332.74" y="71.12" size="1.27" layer="94" ratio="10">9. Change bypass caps to mix of 100nF and 10nF.</text>
-<text x="332.74" y="73.66" size="1.27" layer="94" ratio="10">10. Add hdr for speaker.</text>
-<text x="332.74" y="76.2" size="1.27" layer="94" ratio="10">11. Change C43, C44, C45 to 100pF</text>
-<text x="332.74" y="78.74" size="1.27" layer="94" ratio="10">12. Change C23 to 25V.</text>
-<text x="332.74" y="81.28" size="1.27" layer="94" ratio="10">13 Added PTT SW network to permit DFU mode on power up.</text>
-<text x="330.2" y="83.82" size="1.27" layer="94" ratio="10">05/28/2014</text>
-<text x="332.74" y="86.36" size="1.27" layer="94" ratio="10">14. Change Reset switch to header.</text>
 <text x="91.44" y="27.94" size="1.778" layer="94" ratio="10">INTERNAL SPEAKER</text>
-<text x="332.74" y="88.9" size="1.27" layer="94" ratio="10">15. Power electret mic from  VDD</text>
-<text x="332.74" y="91.44" size="1.27" layer="94" ratio="10">16. Change CN1 to 3-pin</text>
-<text x="330.2" y="93.98" size="1.27" layer="94" ratio="10">05/29/2014</text>
-<text x="332.74" y="96.52" size="1.27" layer="94" ratio="10">17. Change SCL, SDA pulldowns to pullups.</text>
-<text x="330.2" y="106.68" size="1.27" layer="94" ratio="10">06/01/2014</text>
-<text x="332.74" y="99.06" size="1.27" layer="94" ratio="10">18. Delete STLINK LED &amp; components.</text>
-<text x="332.74" y="101.6" size="1.27" layer="94" ratio="10">19. Delete USB fault LED &amp; circuitry.</text>
-<text x="332.74" y="104.14" size="1.27" layer="94" ratio="10">20. Delete VUSB Led &amp; circuitry.</text>
-<text x="332.74" y="109.22" size="1.27" layer="94" ratio="10">21. Add SELECT &amp; BACK switches.</text>
-<text x="330.2" y="111.76" size="1.27" layer="94" ratio="10">06/02/2014</text>
-<text x="332.74" y="114.3" size="1.27" layer="94" ratio="10">22. Change 0603 resistors to IPC packages &amp; symbols.</text>
-<text x="330.2" y="119.38" size="1.27" layer="94" ratio="10">06/05/2014</text>
-<text x="332.74" y="116.84" size="1.27" layer="94" ratio="10">23. Change 0603 caps to IPC packages &amp; symbols.</text>
 <text x="355.6" y="266.7" size="1.4224" layer="94" ratio="10">06/13/14</text>
 <text x="368.3" y="266.7" size="1.4224" layer="94" ratio="10">Release for Prototype</text>
 <text x="419.1" y="266.7" size="1.4224" layer="94" ratio="10">B</text>
 <text x="424.18" y="266.7" size="1.4224" layer="94" ratio="10">RGB</text>
-<text x="330.2" y="127" size="1.27" layer="94" ratio="10">06/12/2014</text>
-<text x="332.74" y="121.92" size="1.27" layer="94" ratio="10">24. Change D3 to BAT60</text>
-<text x="332.74" y="124.46" size="1.27" layer="94" ratio="10">25. Change SW3 back to PBH2UUENAGX</text>
-<text x="332.74" y="129.54" size="1.27" layer="94" ratio="10">26. Remove signals from pins 9 &amp; 10 CN12.</text>
-<text x="332.74" y="132.08" size="1.27" layer="94" ratio="10">27. Change C10 &amp; C12 to Ceramic 0603 caps.</text>
-<text x="332.74" y="134.62" size="1.27" layer="94" ratio="10">28. Change C8 to 10nF.</text>
-<text x="332.74" y="137.16" size="1.27" layer="94" ratio="10">29. Change R12, R13, R15, R16 &amp; R17 to 680 Ohms.</text>
-<text x="332.74" y="139.7" size="1.27" layer="94" ratio="10">30. Change R1, R7 &amp; R8 to 10K</text>
-<text x="332.74" y="142.24" size="1.27" layer="94" ratio="10">31. Correct pinout for LD3985.</text>
-<text x="332.74" y="144.78" size="1.27" layer="94" ratio="10">32. Change C2 &amp; C3 to 20pF.</text>
-<text x="332.74" y="147.32" size="1.27" layer="94" ratio="10">33. Change C27 to 22pF.</text>
-<text x="332.74" y="149.86" size="1.27" layer="94" ratio="10">34. Change C40 to 25V.</text>
-<text x="332.74" y="152.4" size="1.27" layer="94" ratio="10">35. Move Pot R52 to T1 output &amp; change to 1K.</text>
-<text x="332.74" y="154.94" size="1.27" layer="94" ratio="10">36. Change C39 to 220uF,25V</text>
-<text x="330.2" y="160.02" size="1.27" layer="94" ratio="10">06/15/2014</text>
-<text x="332.74" y="157.48" size="1.27" layer="94" ratio="10">37. Change GND  on CN12-12,13 to RF </text>
-<text x="332.74" y="162.56" size="1.27" layer="94" ratio="10">38. Add test points at pins 77,78,79,80.
-PA15,PC10,PC11,PC12</text>
-<text x="332.74" y="167.64" size="1.27" layer="94" ratio="10">39. Add test points at pins 97,98,1,2.
-PE0,PE1,PE2,PE3</text>
-<text x="332.74" y="172.72" size="1.27" layer="94" ratio="10">40. Add test points at pins 24,25,29,30.
-AIN1,AIN2,DAC1,DAC2</text>
-<text x="332.74" y="177.8" size="1.27" layer="94" ratio="10">41. Add test points P14,P16,P18 (GND).</text>
-<text x="332.74" y="180.34" size="1.27" layer="94" ratio="10">42. Add test points P13,p15,p17 (VDD).</text>
-<text x="332.74" y="182.88" size="1.27" layer="94" ratio="10">43. Add test point P19 (+5V).</text>
-<text x="332.74" y="185.42" size="1.27" layer="94" ratio="10">44. Add test point P20 (+VIN ).</text>
-<text x="330.2" y="187.96" size="1.27" layer="94" ratio="10">06/16/2014</text>
-<text x="332.74" y="190.5" size="1.27" layer="94" ratio="10">45. Added 1nf cap in parallel with C46.</text>
-<text x="332.74" y="193.04" size="1.27" layer="94" ratio="10">46. Ad 10nF cap across CN3.</text>
-<text x="332.74" y="195.58" size="1.27" layer="94" ratio="10">47. Replaced FB5 with 10 Ohm 1206 Wide resistor.</text>
 <wire x1="327.66" y1="200.66" x2="327.66" y2="45.72" width="0.1524" layer="94" style="longdash"/>
-<text x="332.74" y="198.12" size="1.27" layer="94" ratio="10">48. Aded 1K resistor in series with FB4.</text>
-<text x="332.74" y="200.66" size="1.27" layer="94" ratio="10">49. Changed C34 to 1nF.</text>
-<text x="330.2" y="205.74" size="1.27" layer="94" ratio="10">06/17/2014</text>
-<text x="332.74" y="203.2" size="1.27" layer="94" ratio="10">50. Changed Select &amp; Back circuits to match PTT.</text>
 <wire x1="327.66" y1="200.66" x2="327.66" y2="279.4" width="0.1524" layer="94" style="longdash"/>
-<text x="332.74" y="208.28" size="1.4224" layer="94" ratio="10">51.Correct XTAL cap value to 20pFfrom 20nF.</text>
-<text x="332.74" y="210.82" size="1.4224" layer="94" ratio="10">52. Change C27 value to 20pF to combine with other 20pF caps.</text>
-<text x="332.74" y="213.36" size="1.4224" layer="94" ratio="10">53. Change C34 to 25V to combine with C1.</text>
-<text x="330.2" y="215.9" size="1.27" layer="94" ratio="10">06/18/2014</text>
 </plain>
 <instances>
 <instance part="CN5" gate="G$1" x="30.48" y="129.54" smashed="yes" rot="MR180">
@@ -6338,13 +6318,6 @@ AIN1,AIN2,DAC1,DAC2</text>
 <instance part="U$7" gate="G$1" x="63.5" y="266.7" smashed="yes">
 <attribute name="VALUE" x="60.96" y="266.954" size="1.4224" layer="96" ratio="9"/>
 </instance>
-<instance part="J7" gate="G$1" x="93.98" y="259.08" smashed="yes" rot="R180">
-<attribute name="NAME" x="93.98" y="256.54" size="1.4224" layer="95" rot="R180"/>
-<attribute name="VALUE" x="96.52" y="254" size="1.4224" layer="96" ratio="9" rot="R180"/>
-</instance>
-<instance part="SH6" gate="G$1" x="91.44" y="264.16" smashed="yes">
-<attribute name="NAME" x="90.678" y="266.192" size="1.4224" layer="95" ratio="9"/>
-</instance>
 <instance part="V17" gate="G$1" x="76.2" y="165.1" smashed="yes">
 <attribute name="VALUE" x="73.66" y="168.148" size="1.4224" layer="95" ratio="9"/>
 </instance>
@@ -6356,8 +6329,8 @@ AIN1,AIN2,DAC1,DAC2</text>
 <instance part="P3" gate="G$1" x="27.94" y="66.04" rot="R180"/>
 <instance part="P4" gate="G$1" x="129.54" y="127" rot="R180"/>
 <instance part="C1" gate="G$1" x="101.6" y="251.46" smashed="yes" rot="R90">
-<attribute name="NAME" x="96.52" y="264.16" size="1.4224" layer="95"/>
-<attribute name="VALUE" x="96.52" y="261.62" size="1.4224" layer="96"/>
+<attribute name="NAME" x="96.52" y="266.7" size="1.4224" layer="95"/>
+<attribute name="VALUE" x="96.52" y="264.16" size="1.4224" layer="96"/>
 </instance>
 <instance part="V118" gate="GND" x="101.6" y="241.3" smashed="yes">
 <attribute name="VALUE" x="99.06" y="237.998" size="1.4224" layer="96" ratio="9"/>
@@ -6374,6 +6347,7 @@ AIN1,AIN2,DAC1,DAC2</text>
 <attribute name="NAME" x="63.5" y="133.604" size="1.4224" layer="95"/>
 <attribute name="VALUE" x="63.5" y="128.778" size="1.4224" layer="96"/>
 </instance>
+<instance part="R21" gate="G$1" x="91.44" y="259.08"/>
 </instances>
 <busses>
 </busses>
@@ -6739,13 +6713,13 @@ AIN1,AIN2,DAC1,DAC2</text>
 <pinref part="C46" gate="G$1" pin="1"/>
 <wire x1="109.22" y1="256.54" x2="109.22" y2="259.08" width="0.1524" layer="91"/>
 <junction x="109.22" y="259.08"/>
-<pinref part="J7" gate="G$1" pin="1"/>
 <wire x1="96.52" y1="259.08" x2="101.6" y2="259.08" width="0.1524" layer="91"/>
 <wire x1="101.6" y1="259.08" x2="109.22" y2="259.08" width="0.1524" layer="91"/>
 <wire x1="124.46" y1="261.62" x2="124.46" y2="259.08" width="0.1524" layer="91"/>
 <pinref part="C1" gate="G$1" pin="2"/>
 <wire x1="101.6" y1="256.54" x2="101.6" y2="259.08" width="0.1524" layer="91"/>
 <junction x="101.6" y="259.08"/>
+<pinref part="R21" gate="G$1" pin="2"/>
 </segment>
 </net>
 <net name="N$43" class="0">
@@ -7352,9 +7326,9 @@ AIN1,AIN2,DAC1,DAC2</text>
 <pinref part="SW3" gate="G$1" pin="6"/>
 <wire x1="78.74" y1="256.54" x2="78.74" y2="259.08" width="0.1524" layer="91"/>
 <wire x1="78.74" y1="259.08" x2="83.82" y2="259.08" width="0.1524" layer="91"/>
-<wire x1="83.82" y1="259.08" x2="88.9" y2="259.08" width="0.1524" layer="91"/>
+<wire x1="83.82" y1="259.08" x2="86.36" y2="259.08" width="0.1524" layer="91"/>
 <junction x="83.82" y="259.08"/>
-<pinref part="J7" gate="G$1" pin="2"/>
+<pinref part="R21" gate="G$1" pin="1"/>
 </segment>
 </net>
 <net name="APTT" class="0">

diff --git a/smartmic/SM1000-REV-B2/TDIM-SM1000-REV-B2.pdf b/smartmic/SM1000-REV-B2/TDIM-SM1000-REV-B2.pdf
new file mode 100644 (file)
index 0000000..26ce1ad
Binary files /dev/null and b/smartmic/SM1000-REV-B2/TDIM-SM1000-REV-B2.pdf differ