From: drowe67 <drowe67@01035d8c-6547-0410-b346-abe4f91aad63>
Date: Mon, 18 May 2015 20:17:06 +0000 (+0000)
Subject: corrected file name and added a few items
X-Git-Url: http://git.whiteaudio.com/gitweb/?a=commitdiff_plain;h=69939464598d7a6a142d93ecc7a9c55cfe00029f;p=freetel-svn-tracking.git

corrected file name and added a few items

git-svn-id: https://svn.code.sf.net/p/freetel/code@2136 01035d8c-6547-0410-b346-abe4f91aad63
---

diff --git a/smartmic/SM1000-E/SM100-E-change-log.txt b/smartmic/SM1000-E/SM100-E-change-log.txt
deleted file mode 100644
index ee4ea439..00000000
--- a/smartmic/SM1000-E/SM100-E-change-log.txt
+++ /dev/null
@@ -1,57 +0,0 @@
-SM1000-E-CHANGE-LOG.TXT
-03/30/15 RGB
-
-1.  [X]	Change PTT sw. to e-switch LC2259OANP.
-
-2.  [X]	Change POWER SW to e-switch LC2259EENP.
-	
-3.  [X]	Change SPKR CONN J4 to CONN-BOOM-XH-2A.
-
-4.  [ ]	Added part outlines to layer tDocu for documentation.
-
-   	In progress, adding to outlines in time.
-
-05/18/15
-
-5.  [ ]	Problem with SPKR OUT conn. Shorts output when stereo jack used.
-
-6.  [ ]	TrimPOT holes, location off by 1mm.
-
-7.  [X]	U1, CPU pins extend to the end of the pads.
-
-		Corrected RGB
-
-8.  [X]	Lad pattern for LEDs too large. I will look into this. RGB
-
-		No action todate.
-
-9.  [X]	SW5 land pattern too wide. Check specification.
-
-		Corrected footprint RGB
-
-10. [X]	C32, C59 footprint too short.
-
-		corrected  RGB
-
-11. [X]	L1 Land pattern too wide.
-
-		Corrected RGB
-
-12  [ ]	CN4	Bubble after SMT(high temperature)
-
-		No action yet. Edwin, can you find an alternative to fit? If different footprint, let me know and send specification so
-		I can change it.(RGB)
-
-13. [X]	R46	Easy to break R46 with handling.
-
-		Add cement after production.
-
-14. [ ]	PCB	Problem reflowing CN10 USB connector.
-		
-		Make Breakaway 10mm (Edwin)
-
-15  [ ]	PCB	Stencil too small.
-		
-		MAke Stencil 52 x 52 cm(Edwin)
-	
-		
diff --git a/smartmic/SM1000-E/SM1000-E-change-log.txt b/smartmic/SM1000-E/SM1000-E-change-log.txt
new file mode 100644
index 00000000..e8c55e73
--- /dev/null
+++ b/smartmic/SM1000-E/SM1000-E-change-log.txt
@@ -0,0 +1,65 @@
+SM1000-E-CHANGE-LOG.TXT
+03/30/15 RGB
+
+1.  [X]	Change PTT sw. to e-switch LC2259OANP.
+
+2.  [X]	Change POWER SW to e-switch LC2259EENP.
+	
+3.  [X]	Change SPKR CONN J4 to CONN-BOOM-XH-2A.
+
+4.  [ ]	Added part outlines to layer tDocu for documentation.
+
+   	In progress, adding to outlines in time.
+
+05/18/15
+
+5.  [ ]	Problem with SPKR OUT conn. Shorts output when stereo jack used.
+        + as per Josh Mesaline email, suggest resistors to tip and ring
+          so a short doesn't upset amp.  Does this mean it will work with
+          mono and stereo plugs?  If stereo only we should note this in UG.
+
+6.  [ ]	TrimPOT holes, location off by 1mm.
+
+7.  [X]	U1, CPU pins extend to the end of the pads.
+
+		Corrected RGB
+
+8.  [X]	Lad pattern for LEDs too large. I will look into this. RGB
+
+		No action todate.
+
+9.  [X]	SW5 land pattern too wide. Check specification.
+
+		Corrected footprint RGB
+
+10. [X]	C32, C59 footprint too short.
+
+		corrected  RGB
+
+11. [X]	L1 Land pattern too wide.
+
+		Corrected RGB
+
+12  [ ]	CN4	Bubble after SMT(high temperature)
+
+		No action yet. Edwin, can you find an alternative to fit? If different footprint, let me know and send specification so
+		I can change it.(RGB)
+
+13. [X]	R46	Easy to break R46 with handling.
+
+		Add cement after production.
+
+14. [ ]	PCB	Problem reflowing CN10 USB connector.
+		
+		Make Breakaway 10mm (Edwin)
+
+15  [ ]	PCB	Stencil too small.
+		
+		MAke Stencil 52 x 52 cm(Edwin)
+	
+16  [ ] Firmware   Better debouncing software for push button switches (DR)	
+
+17  [ ] Enclosure  Move "Speaker Volume" text lower to clear volume control knob
+
+18  [ ] Enclosure  Some variablility in gap between lid and front panel, gap is
+                   sometimes wider on one side than another (Edwin)